Home
BACnet points lists
Contemporary Controls
ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX

Variable frequency drive (HVAC) · BACnet points list

Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet points list

Q: How many BACnet points does the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX have?

This list has 609 BACnet objects: 546 analog inputs, 4 analog outputs, 59 binary inputs. The exact set on a given unit depends on its firmware, installed options and configuration.

Q: Which Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet points are writable?

4 of the 609 objects accept a write. Points marked Command have a priority array: a write holds until it is released, so release it back to automatic when you are done. The source has no read/write column, so this is inferred from object type.

Q: Where is the official Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet documentation?

The source is BASgatewayLX Modbus device profile ABB_Drive_DCU_5305_is_1_a (ABB_Drive_DCU_5305_is_1_a_LX.csv), published free by Contemporary Controls at https://www.ccontrols.com/support/dp/ABB_Drive_DCU_5305_is_1_a_LX.zip.

Q: What are the minimum BACnet points to integrate the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX?

Start with AO 74 ACH550 CONTROL WORD LSW (DCU control word, low word: start/stop, reset bits); AO 63 Reference 1 (Speed reference REF1); BI 30 RUNNING (Drive running); AI 90 OUTPUT FREQ (Output frequency, Hz); AI 89 SPEED (Motor speed, rpm); AI 91 CURRENT (Motor current, A); AI 93 POWER (Output power, kW); BI 43 ALARM (Any active alarm); BI 42 FAULT (Drive tripped on a fault); AI 144 FAULT WORD 1 (Fault bits, word 1).

Q: How do I check these points on the real ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX?

Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.

Updated 12 November 2026

Short answer

Gateway profile for the ABB ACH550 when its embedded fieldbus uses the DCU control profile: 609 objects (546 AI, 4 AO, 59 BI), 138 polled by default. Coil and status bits (STOP, START, RUNNING, FAULT, ALARM), the 16- and 32-bit control/status words, the actual signals and the whole parameter list are mapped. Four Analog Outputs write the control words and the two references.

This page lists 609 BACnet objects for the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX — 4 of them writable — with each object’s type, instance number, name, engineering units and access. It is re-typed from Contemporary Controls’s own free documentation, linked below.

Manufacturer: Contemporary Controls
Model: ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX
Equipment: Variable frequency drive (HVAC)
Equipment type: VFDs & pumps
BACnet objects: 609 (4 writable)
Transport: BACnet IP
Firmware: Not stated
Also known as: ACH550, ACH550 DCU profile, ABB_Drive_DCU_5305_is_1
Source document: BASgatewayLX Modbus device profile ABB_Drive_DCU_5305_is_1_a · ABB_Drive_DCU_5305_is_1_a_LX.csv

Download CSV 609 rows Download EDE B.I.G.-EU JSON Manufacturer PDF ↗ Compare with your scan Download Easy BACnet Mobile App Google Play

Reference only, provided as-is: verify against Contemporary Controls’s current documentation and the live device before use. Not official Contemporary Controls information. Terms of use.

BMS integration notes: Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX

Integration in brief

Set the drive for fieldbus control (EXT1 commands and reference = COMM) and 5305 = 1. With the DCU profile the drive takes start/stop from the ACH550 control word (AO 74, register 40031); write the speed reference to Reference 1 (AO 63). Read RUNNING, FAULT, ALARM and the actual values.

Minimum points to map

The short list most integrators start with — enough to run the unit from a BMS. Map more as the job needs.

Object	Name	Why	Access
AO 74	ACH550 CONTROL WORD LSW	DCU control word, low word: start/stop, reset bits	Command
AO 63	Reference 1	Speed reference REF1	Command
BI 30	RUNNING	Drive running	Read
AI 90	OUTPUT FREQ	Output frequency, Hz	Read
AI 89	SPEED	Motor speed, rpm	Read
AI 91	CURRENT	Motor current, A	Read
AI 93	POWER	Output power, kW	Read
BI 43	ALARM	Any active alarm	Read
BI 42	FAULT	Drive tripped on a fault	Read
AI 144	FAULT WORD 1	Fault bits, word 1	Read

Enable & remote start

Set EXT1 commands (parameter 1001) to 10 (COMM) and the speed reference source to COMM as the ACH550 manual describes, and parameter 5305 = 1. In this mode start/stop comes from register 40031 (AO 74), not 40001.

Network setup

The BASgatewayLX presents each Modbus device as its own virtual BACnet device on BACnet IP; give it a unique device instance and Modbus address (serial) or IP address (Modbus TCP) when you add it with this profile.
One BASgatewayLX handles up to 100 Modbus devices and 1000 polled points in total, so leave unneeded rows unpolled.

Watch out for

ACH550 parameter 5305 (EFB CTRL PROFILE) selects the control profile: 0 = ABB DRV LIM, 1 = DCU PROFILE, 2 = ABB DRV FULL. Load the BASgatewayLX profile that matches it.
AO 62 (register 40001) is the ABB DRV control word; with 5305 = 1 the drive uses the ACH550 control word at 40031 (AO 74) instead.
Unpolled rows do not appear as BACnet objects until enabled in the gateway's device profile page.

Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet objects

Type: AI, AO, AV, BI, BO, BV, MI/MO/MV (multi-state) · Access: Read read-only, Write writable, Command writable with a priority array.

Note: the source document has no read/write column, so access here is inferred from the object type (inputs read-only, values writable). Confirm on the live controller before writing.

609 of 609 shown

Type

Binary

Access

Units

Show

Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet Points List
			Description
BI	1	STOP	Modbus 000001		Read
BI	2	START	Modbus 000002		Read
BI	3	REVERSE	Modbus 000003		Read
BI	4	LOCAL	Modbus 000004		Read
BI	5	RESET	Modbus 000005		Read
BI	6	EXT2	Modbus 000006		Read
BI	7	RUN_DISABLE	Modbus 000007		Read
BI	8	STPMODE_R	Modbus 000008		Read
BI	9	STPMODE_EM	Modbus 000009		Read
BI	10	STPMODE_C	Modbus 000010		Read
BI	11	RAMP_2	Modbus 000011		Read
BI	12	RAMP_OUT_0	Modbus 000012		Read
BI	13	RAMP_HOLD	Modbus 000013		Read
BI	14	RAMP_IN_0	Modbus 000014		Read
BI	15	REQ_LOCALLOCK	Modbus 000015		Read
BI	16	TORQLIM2	Modbus 000016		Read
BI	17	FBLOCAL_CTL	Modbus 000017		Read
BI	18	FBLOCAL_REF	Modbus 000018		Read
BI	19	START_DISABLE1	Modbus 000019		Read
BI	20	START_DISABLE2	Modbus 000020		Read
BI	21	Relay Output 1	Modbus 000033		Read
BI	22	Relay Output 2	Modbus 000034		Read
BI	23	Relay Output 3	Modbus 000035		Read
BI	24	Relay Output 4	Modbus 000036		Read
BI	25	Relay Output 5	Modbus 000037		Read
BI	26	Relay Output 6	Modbus 000038		Read
BI	27	READY	Modbus 100001		Read
BI	28	ENABLED	Modbus 100002		Read
BI	29	STARTED	Modbus 100003		Read
BImin	30	RUNNING	Modbus 100004		Read
BI	31	ZERO_SPEED	Modbus 100005		Read
BI	32	ACCELERATE	Modbus 100006		Read
BI	33	DECELERATE	Modbus 100007		Read
BI	34	AT_SETPOINT	Modbus 100008		Read
BI	35	LIMIT	Modbus 100009		Read
BI	36	SUPERVISION	Modbus 100010		Read
BI	37	REV_REF	Modbus 100011		Read
BI	38	REV_ACT	Modbus 100012		Read
BI	39	PANEL_LOCAL	Modbus 100013		Read
BI	40	FIELDBUS_LOCAL	Modbus 100014		Read
BI	41	EXT2_ACT	Modbus 100015		Read
BImin	42	FAULT	Modbus 100016		Read
BImin	43	ALARM	Modbus 100017		Read
BI	44	REQ_MAINT	Modbus 100018		Read
BI	45	DIRLOCK	Modbus 100019		Read
BI	46	LOCALLOCK	Modbus 100020		Read
BI	47	CTL_MODE	Modbus 100021		Read
BI	48	REQ_CTL	Modbus 100027		Read
BI	49	REQ_REF1	Modbus 100028		Read
BI	50	REQ_REF2	Modbus 100029		Read
BI	51	REQ_REF2EXT	Modbus 100030		Read
BI	52	ACK_STARTINH	Modbus 100031		Read
BI	53	ACK_OFF_ILCK	Modbus 100032		Read
BI	54	DI1	Modbus 100033		Read
BI	55	DI2	Modbus 100034		Read
BI	56	DI3	Modbus 100035		Read
BI	57	DI4	Modbus 100036		Read
BI	58	DI5	Modbus 100037		Read
BI	59	DI6	Modbus 100038		Read
AI	60	AI1	Modbus 300001	%	Read
AI	61	AI2	Modbus 300002	%	Read
AO	62	CONTROL WORD	Modbus 400001		Command
AOmin	63	Reference 1	Modbus 400002		Command
AO	64	Reference 2	Modbus 400003		Command
AI	65	STATUS WORD	Modbus 400004		Read
AI	66	Actual 1	Modbus 400005		Read
AI	67	Actual 2	Modbus 400006		Read
AI	68	Actual 3	Modbus 400007		Read
AI	69	Actual 4	Modbus 400008		Read
AI	70	Actual 5	Modbus 400009		Read
AI	71	Actual 6	Modbus 400010		Read
AI	72	Actual 7	Modbus 400011		Read
AI	73	Actual 8	Modbus 400012		Read
AOmin	74	ACH550 CONTROL WORD LSW	Modbus 400031		Command
AI	75	ACH550 CONTROL WORD MSW	Modbus 400032		Read
AI	76	ACH550 STATUS WORD LSW	Modbus 400033		Read
AI	77	ACH550 STATUS WORD MSW	Modbus 400034		Read
AI	78	LANGUAGE	Modbus 409901; not polled by default		Read
AI	79	APPLIC MACRO	Modbus 409902; not polled by default		Read
AI	80	MOTOR CTRL MODE	Modbus 409904; not polled by default		Read
AI	81	MOTOR NOM VOLT	Modbus 409905; not polled by default	V	Read
AI	82	MOTOR NOM CURR	Modbus 409906; not polled by default	A	Read
AI	83	MOTOR NOM FREQ	Modbus 409907; not polled by default	Hz	Read
AI	84	MOTOR NOM SPEED	Modbus 409908; not polled by default	rpm	Read
AI	85	MOTOR NOM POWER	Modbus 409909; not polled by default	hp	Read
AI	86	ID RUN	Modbus 409910; not polled by default		Read
AI	87	MOTOR COSPHI	Modbus 409915; not polled by default		Read
AI	88	SPEED DIR	Modbus 400101	rpm	Read
AImin	89	SPEED	Modbus 400102	rpm	Read
AImin	90	OUTPUT FREQ	Modbus 400103	Hz	Read
AImin	91	CURRENT	Modbus 400104	A	Read
AI	92	TORQUE	Modbus 400105	%	Read
AImin	93	POWER	Modbus 400106	kW	Read
AI	94	DC BUS VOLTAGE	Modbus 400107	V	Read
AI	95	OUTPUT VOLTAGE	Modbus 400109	V	Read
AI	96	DRIVE TEMP	Modbus 400110	°C	Read
AI	97	EXTERNAL REF 1	Modbus 400111	rpm	Read
AI	98	EXTERNAL REF 2	Modbus 400112	%	Read
AI	99	CTRL LOCATION	Modbus 400113		Read
AI	100	RUN TIME (R)	Modbus 400114		Read
AI	101	KWH COUNTER (R)	Modbus 400115	kWh	Read
AI	102	APPL BLK OUTPUT	Modbus 400116	%	Read
AI	103	DI 1-3 STATUS	Modbus 400118		Read
AI	104	DI 4-6 STATUS	Modbus 400119		Read
AI	105	AI 1	Modbus 400120	%	Read
AI	106	AI 2	Modbus 400121	%	Read
AI	107	RO 1-3 STATUS	Modbus 400122		Read
AI	108	RO 4-6 STATUS	Modbus 400123		Read
AI	109	AO 1	Modbus 400124	mA	Read
AI	110	AO 2	Modbus 400125	mA	Read
AI	111	PID 1 OUTPUT	Modbus 400126	%	Read
AI	112	PID 2 OUTPUT	Modbus 400127	%	Read
AI	113	PID 1 SETPNT	Modbus 400128		Read
AI	114	PID 2 SETPNT	Modbus 400129		Read
AI	115	PID 1 FBK	Modbus 400130		Read
AI	116	PID 2 FBK	Modbus 400131		Read
AI	117	PID 1 DEVIATION	Modbus 400132		Read
AI	118	PID 2 DEVIATION	Modbus 400133		Read
AI	119	COMM RO WORD	Modbus 400134		Read
AI	120	COMM VALUE 1	Modbus 400135		Read
AI	121	COMM VALUE 2	Modbus 400136		Read
AI	122	PROCESS VAR 1	Modbus 400137		Read
AI	123	PROCESS VAR 2	Modbus 400138		Read
AI	124	PROCESS VAR 3	Modbus 400139		Read
AI	125	RUN TIME	Modbus 400140		Read
AI	126	MWH COUNTER	Modbus 400141	MWh	Read
AI	127	REVOLUTION CNTR	Modbus 400142		Read
AI	128	DRIVE ON TIME HI	Modbus 400143	days	Read
AI	129	DRIVE ON TIME LO	Modbus 400144		Read
AI	130	MOTOR TEMP	Modbus 400145		Read
AI	131	CB TEMP	Modbus 400150	°C	Read
AI	132	MOT THERM STRESS	Modbus 400153	%	Read
AI	133	PID COMM VALUE 1	Modbus 400158		Read
AI	134	PID COMM VALUE 2	Modbus 400159		Read
AI	135	SAVED KWH	Modbus 400174	kWh	Read
AI	136	SAVED MWH	Modbus 400175	MWh	Read
AI	137	SAVED AMOUNT 1	Modbus 400176		Read
AI	138	SAVED AMOUNT 2	Modbus 400177		Read
AI	139	SAVED CO2	Modbus 400178	tons	Read
AI	140	FB CMD WORD 1	Modbus 400301		Read
AI	141	FB CMD WORD 2	Modbus 400302		Read
AI	142	FB STS WORD 1	Modbus 400303		Read
AI	143	FB STS WORD 2	Modbus 400304		Read
AImin	144	FAULT WORD 1	Modbus 400305		Read
AI	145	FAULT WORD 2	Modbus 400306		Read
AI	146	FAULT WORD 3	Modbus 400307		Read
AI	147	ALARM WORD 1	Modbus 400308		Read
AI	148	ALARM WORD 2	Modbus 400309		Read
AI	149	LAST FAULT	Modbus 400401; not polled by default		Read
AI	150	FAULT TIME 1	Modbus 400402; not polled by default	days	Read
AI	151	FAULT TIME 2	Modbus 400403; not polled by default		Read
AI	152	SPEED AT FLT	Modbus 400404; not polled by default	rpm	Read
AI	153	FREQ AT FLT	Modbus 400405; not polled by default	Hz	Read
AI	154	VOLTAGE AT FLT	Modbus 400406; not polled by default	V	Read
AI	155	CURRENT AT FLT	Modbus 400407; not polled by default	A	Read
AI	156	TORQUE AT FLT	Modbus 400408; not polled by default	%	Read
AI	157	STATUS AT FLT	Modbus 400409; not polled by default		Read
AI	158	DI 1-3 AT FLT	Modbus 400410; not polled by default		Read
AI	159	DI 4-6 AT FLT	Modbus 400411; not polled by default		Read
AI	160	PREVIOUS FAULT 1	Modbus 400412; not polled by default		Read
AI	161	PREVIOUS FAULT 2	Modbus 400413; not polled by default		Read
AI	162	EXT1 COMMANDS	Modbus 401001; not polled by default		Read
AI	163	EXT2 COMMANDS	Modbus 401002; not polled by default		Read
AI	164	DIRECTION	Modbus 401003; not polled by default		Read
AI	165	KEYPAD REF SEL	Modbus 401101; not polled by default		Read
AI	166	EXT1/EXT2 SEL	Modbus 401102; not polled by default		Read
AI	167	REF1 SELECT	Modbus 401103; not polled by default		Read
AI	168	REF1 MIN	Modbus 401104; not polled by default	rpm	Read
AI	169	REF1 MAX	Modbus 401105; not polled by default	rpm	Read
AI	170	REF2 SELECT	Modbus 401106; not polled by default		Read
AI	171	REF2 MIN	Modbus 401107; not polled by default	%	Read
AI	172	REF2 MAX	Modbus 401108; not polled by default	%	Read
AI	173	CONST SPEED SEL	Modbus 401201; not polled by default		Read
AI	174	CONST SPEED 1	Modbus 401202; not polled by default	rpm	Read
AI	175	CONST SPEED 2	Modbus 401203; not polled by default	rpm	Read
AI	176	CONST SPEED 3	Modbus 401204; not polled by default	rpm	Read
AI	177	CONST SPEED 4	Modbus 401205; not polled by default	rpm	Read
AI	178	CONST SPEED 5	Modbus 401206; not polled by default	rpm	Read
AI	179	CONST SPEED 6	Modbus 401207; not polled by default	rpm	Read
AI	180	CONST SPEED 7	Modbus 401208; not polled by default	rpm	Read
AI	181	TIMED MODE SEL	Modbus 401209; not polled by default		Read
AI	182	MINIMUM AI1	Modbus 401301; not polled by default	%	Read
AI	183	MAXIMUM AI1	Modbus 401302; not polled by default	%	Read
AI	184	FILTER AI1	Modbus 401303; not polled by default	s	Read
AI	185	MINIMUM AI2	Modbus 401304; not polled by default	%	Read
AI	186	MAXIMUM AI2	Modbus 401305; not polled by default	%	Read
AI	187	FILTER AI2	Modbus 401306; not polled by default	s	Read
AI	188	RELAY OUTPUT 1	Modbus 401401; not polled by default		Read
AI	189	RELAY OUTPUT 2	Modbus 401402; not polled by default		Read
AI	190	RELAY OUTPUT 3	Modbus 401403; not polled by default		Read
AI	191	RO 1 ON DELAY	Modbus 401404; not polled by default	s	Read
AI	192	RO 1 OFF DELAY	Modbus 401405; not polled by default	s	Read
AI	193	RO 2 ON DELAY	Modbus 401406; not polled by default	s	Read
AI	194	RO 2 OFF DELAY	Modbus 401407; not polled by default	s	Read
AI	195	RO 3 ON DELAY	Modbus 401408; not polled by default	s	Read
AI	196	RO 3 OFF DELAY	Modbus 401409; not polled by default	s	Read
AI	197	RELAY OUTPUT 4	Modbus 401410; not polled by default		Read
AI	198	RELAY OUTPUT 5	Modbus 401411; not polled by default		Read
AI	199	RELAY OUTPUT 6	Modbus 401412; not polled by default		Read
AI	200	RO 4 ON DELAY	Modbus 401413; not polled by default	s	Read
AI	201	RO 4 OFF DELAY	Modbus 401414; not polled by default	s	Read
AI	202	RO 5 ON DELAY	Modbus 401415; not polled by default	s	Read
AI	203	RO 5 OFF DELAY	Modbus 401416; not polled by default	s	Read
AI	204	RO 6 ON DELAY	Modbus 401417; not polled by default	s	Read
AI	205	RO 6 OFF DELAY	Modbus 401418; not polled by default	s	Read
AI	206	AO1 CONTENT SEL	Modbus 401501; not polled by default	Hz	Read
AI	207	AO1 CONTENT MIN	Modbus 401502; not polled by default	Hz	Read
AI	208	AO1 CONTENT MAX	Modbus 401503; not polled by default	Hz	Read
AI	209	MINIMUM AO1	Modbus 401504; not polled by default	mA	Read
AI	210	MAXIMUM AO1	Modbus 401505; not polled by default	mA	Read
AI	211	FILTER AO1	Modbus 401506; not polled by default	s	Read
AI	212	AO2 CONTENT SEL	Modbus 401507; not polled by default	A	Read
AI	213	AO2 CONTENT MIN	Modbus 401508; not polled by default	A	Read
AI	214	AO2 CONTENT MAX	Modbus 401509; not polled by default	A	Read
AI	215	MINIMUM AO2	Modbus 401510; not polled by default	mA	Read
AI	216	MAXIMUM AO2	Modbus 401511; not polled by default	mA	Read
AI	217	FILTER AO2	Modbus 401512; not polled by default	s	Read
AI	218	RUN ENABLE	Modbus 401601; not polled by default		Read
AI	219	PARAMETER LOCK	Modbus 401602; not polled by default		Read
AI	220	PASS CODE	Modbus 401603; not polled by default		Read
AI	221	FAULT RESET sEL	Modbus 401604; not polled by default		Read
AI	222	USER PAR SET CHG	Modbus 401605; not polled by default		Read
AI	223	LOCAL LOCK	Modbus 401606; not polled by default		Read
AI	224	PARAM SAVE	Modbus 401607; not polled by default		Read
AI	225	START ENABLE 1	Modbus 401608; not polled by default		Read
AI	226	START ENABLE 2	Modbus 401609; not polled by default		Read
AI	227	DISPLAY ALARMS	Modbus 401610; not polled by default		Read
AI	228	PARAMETER VIEW	Modbus 401611; not polled by default		Read
AI	229	FAN CONTROL	Modbus 401612; not polled by default		Read
AI	230	FAULT RESET	Modbus 401613; not polled by default		Read
AI	231	OVERRIDE SEL	Modbus 401701; not polled by default		Read
AI	232	OVERRIDE FREQ	Modbus 401702; not polled by default	Hz	Read
AI	233	OVERRIDE SPEED	Modbus 401703; not polled by default	rpm	Read
AI	234	OVERR PASS CODE	Modbus 401704; not polled by default		Read
AI	235	OVERRIDE	Modbus 401705; not polled by default		Read
AI	236	OVERRIDE DIR	Modbus 401706; not polled by default		Read
AI	237	OVERRIDE REF	Modbus 401707; not polled by default		Read
AI	238	MINIMUM SPEED	Modbus 402001; not polled by default	rpm	Read
AI	239	MAXIMUM SPEED	Modbus 402002; not polled by default	rpm	Read
AI	240	MAX CURRENT	Modbus 402003; not polled by default	A	Read
AI	241	UNDERVOLT CTRL	Modbus 402006; not polled by default		Read
AI	242	MINIMUM FREQ	Modbus 402007; not polled by default	Hz	Read
AI	243	MAXIMUM FREQ	Modbus 402008; not polled by default	Hz	Read
AI	244	MIN TORQUE SEL	Modbus 402013; not polled by default		Read
AI	245	MAX TORQUE SEL	Modbus 402014; not polled by default		Read
AI	246	MIN TORQUE 1	Modbus 402015; not polled by default	%	Read
AI	247	MIN TORQUE 2	Modbus 402016; not polled by default	%	Read
AI	248	MAX TORQUE 1	Modbus 402017; not polled by default	%	Read
AI	249	MAX TORQUE 2	Modbus 402018; not polled by default	%	Read
AI	250	START FUNCTION	Modbus 402101; not polled by default		Read
AI	251	STOP FUNCTION	Modbus 402102; not polled by default		Read
AI	252	DC MAGN TIME	Modbus 402103; not polled by default	s	Read
AI	253	DC HOLD CTL	Modbus 402104; not polled by default		Read
AI	254	DC HOLD SPEED	Modbus 402105; not polled by default	rpm	Read
AI	255	DC CURR REF	Modbus 402106; not polled by default	%	Read
AI	256	DC BRAKE TIME	Modbus 402107; not polled by default	s	Read
AI	257	START INHIBIT	Modbus 402108; not polled by default		Read
AI	258	EMERG STOP SEL	Modbus 402109; not polled by default		Read
AI	259	TORQ BOOST CURR	Modbus 402110; not polled by default	%	Read
AI	260	START DELAY	Modbus 402113; not polled by default	s	Read
AI	261	ACC/DEC 1/2 SEL	Modbus 402201; not polled by default		Read
AI	262	ACCELER TIME 1	Modbus 402202; not polled by default	s	Read
AI	263	DECELER TIME 1	Modbus 402203; not polled by default	s	Read
AI	264	RAMP SHAPE 1	Modbus 402204; not polled by default	s	Read
AI	265	ACCELER TIME 2	Modbus 402205; not polled by default	s	Read
AI	266	DECELER TIME 2	Modbus 402206; not polled by default	s	Read
AI	267	RAMP SHAPE 2	Modbus 402207; not polled by default	s	Read
AI	268	EMERG DEC TIME	Modbus 402208; not polled by default	s	Read
AI	269	RAMP INPUT 0	Modbus 402209; not polled by default		Read
AI	270	PROP GAIN	Modbus 402301; not polled by default		Read
AI	271	INTEGRATION TIME	Modbus 402302; not polled by default	s	Read
AI	272	DERIVATION TIME	Modbus 402303; not polled by default	ms	Read
AI	273	ACC COMPENSATION	Modbus 402304; not polled by default	s	Read
AI	274	AUTOTUNE RUN	Modbus 402305; not polled by default		Read
AI	275	CRIT SPEED SEL	Modbus 402501; not polled by default	rpm	Read
AI	276	CRIT SPEED 1 LO	Modbus 402502; not polled by default	rpm	Read
AI	277	CRIT SPEED 1 HI	Modbus 402503; not polled by default	rpm	Read
AI	278	CRIT SPEED 2 LO	Modbus 402504; not polled by default	rpm	Read
AI	279	CRIT SPEED 2 HI	Modbus 402505; not polled by default	rpm	Read
AI	280	CRIT SPEED 3 LO	Modbus 402506; not polled by default	rpm	Read
AI	281	CRIT SPEED 3 HI	Modbus 402507; not polled by default	rpm	Read
AI	282	FLUX OPT ENABLE	Modbus 402601; not polled by default		Read
AI	283	FLUX BRAKING	Modbus 402602; not polled by default		Read
AI	284	IR COMP VOLT	Modbus 402603; not polled by default	V	Read
AI	285	IR COMP FREQ	Modbus 402604; not polled by default	%	Read
AI	286	U/F RATIO	Modbus 402605; not polled by default	kHz	Read
AI	287	SWITCHING FREQ	Modbus 402606; not polled by default		Read
AI	288	SWITCH FREQ CTRL	Modbus 402607; not polled by default	%	Read
AI	289	SLIP COMP RATIO	Modbus 402608; not polled by default		Read
AI	290	NOISE SMOOTHING	Modbus 402609; not polled by default		Read
AI	291	DC STABILIZER	Modbus 402619; not polled by default		Read
AI	292	OVERMODULATION	Modbus 402625; not polled by default		Read
AI	293	COOLING FAN TRIG	Modbus 402901; not polled by default		Read
AI	294	COOLING FAN ACT	Modbus 402902; not polled by default		Read
AI	295	REVOLUTION TRIG	Modbus 402903; not polled by default		Read
AI	296	REVOLUTION ACT	Modbus 402904; not polled by default		Read
AI	297	RUN TIME TRIG	Modbus 402905; not polled by default		Read
AI	298	RUN TIME ACT	Modbus 402906; not polled by default		Read
AI	299	USER MWh TRIG	Modbus 402907; not polled by default	MWh	Read
AI	300	USER MWh ACT	Modbus 402908; not polled by default	MWh	Read
AI	301	AI<MIN FUNCTION	Modbus 403001; not polled by default		Read
AI	302	PANEL COMM ERR	Modbus 403002; not polled by default		Read
AI	303	EXTERNAL FAULT 1	Modbus 403003; not polled by default		Read
AI	304	EXTERNAL FAULT 2	Modbus 403004; not polled by default		Read
AI	305	MOT THERM PROT	Modbus 403005; not polled by default		Read
AI	306	MOT THERM TIME	Modbus 403006; not polled by default	s	Read
AI	307	MOT LOAD CURVE	Modbus 403007; not polled by default	%	Read
AI	308	ZERO SPEED LOAD	Modbus 403008; not polled by default	%	Read
AI	309	BREAK POINT FREQ	Modbus 403009; not polled by default	Hz	Read
AI	310	STALL FUNCTION	Modbus 403010; not polled by default		Read
AI	311	STALL FREQUENCY	Modbus 403011; not polled by default	Hz	Read
AI	312	STALL TIME	Modbus 403012; not polled by default	s	Read
AI	313	EARTH FAULT	Modbus 403017; not polled by default		Read
AI	314	COMM FAULT FUNC	Modbus 403018; not polled by default		Read
AI	315	COMM FAULT TIME	Modbus 403019; not polled by default	s	Read
AI	316	AI1 FAULT LIMIT	Modbus 403021; not polled by default	%	Read
AI	317	AI2 FAULT LIMIT	Modbus 403022; not polled by default	%	Read
AI	318	WIRING FAULT	Modbus 403023; not polled by default		Read
AI	319	CB TEMP FAULT	Modbus 403024; not polled by default		Read
AI	320	EARTH FAULT LVL	Modbus 403028; not polled by default		Read
AI	321	NUMBER OF TRIALS	Modbus 403101; not polled by default		Read
AI	322	TRIAL TIME	Modbus 403102; not polled by default	s	Read
AI	323	DELAY TIME	Modbus 403103; not polled by default	s	Read
AI	324	AR OVERCURRENT	Modbus 403104; not polled by default		Read
AI	325	AR OVERVOLTAGE	Modbus 403105; not polled by default		Read
AI	326	AR UNDERVOLTAGE	Modbus 403106; not polled by default		Read
AI	327	AR AI<MIN	Modbus 403107; not polled by default		Read
AI	328	AR EXTERNAL FLT	Modbus 403108; not polled by default		Read
AI	329	SUPERV 1 PARAM	Modbus 403201; not polled by default	Hz	Read
AI	330	SUPERV 1 LIM LO	Modbus 403202; not polled by default	Hz	Read
AI	331	SUPERV 1 LIM HI	Modbus 403203; not polled by default	Hz	Read
AI	332	SUPERV 2 PARAM	Modbus 403204; not polled by default	A	Read
AI	333	SUPERV 2 LIM LO	Modbus 403205; not polled by default	A	Read
AI	334	SUPERV 2 LIM HI	Modbus 403206; not polled by default	A	Read
AI	335	SUPERV 3 PARAM	Modbus 403207; not polled by default		Read
AI	336	SUPERV 3 LIM LO	Modbus 403208; not polled by default	%	Read
AI	337	SUPERV 3 LIM HI	Modbus 403209; not polled by default	%	Read
AI	338	FIRMWARE	Modbus 403301; not polled by default		Read
AI	339	LOADING PACKAGE	Modbus 403302; not polled by default		Read
AI	340	TEST DATE	Modbus 403303; not polled by default		Read
AI	341	DRIVE RATING	Modbus 403304; not polled by default		Read
AI	342	PARAMETER TABLE	Modbus 403305; not polled by default		Read
AI	343	SIGNAL1 PARAM	Modbus 403401; not polled by default	Hz	Read
AI	344	SIGNAL1 MIN	Modbus 403402; not polled by default	Hz	Read
AI	345	SIGNAL1 MAX	Modbus 403403; not polled by default	Hz	Read
AI	346	OUTPUT1 DSP FORM	Modbus 403404; not polled by default		Read
AI	347	OUTPUT1 UNIT	Modbus 403405; not polled by default	%	Read
AI	348	OUTPUT1 MIN	Modbus 403406; not polled by default	%	Read
AI	349	OUTPUT1 MAX	Modbus 403407; not polled by default	%	Read
AI	350	SIGNAL2 PARAM	Modbus 403408; not polled by default	A	Read
AI	351	SIGNAL2 MIN	Modbus 403409; not polled by default	A	Read
AI	352	SIGNAL2 MAX	Modbus 403410; not polled by default	A	Read
AI	353	OUTPUT2 DSP FORM	Modbus 403411; not polled by default		Read
AI	354	OUTPUT2 UNIT	Modbus 403412; not polled by default	A	Read
AI	355	OUTPUT2 MIN	Modbus 403413; not polled by default	A	Read
AI	356	OUTPUT2 MAX	Modbus 403414; not polled by default	A	Read
AI	357	SIGNAL3 PARAM	Modbus 403415; not polled by default		Read
AI	358	SIGNAL3 MIN	Modbus 403416; not polled by default	%	Read
AI	359	SIGNAL3 MAX	Modbus 403417; not polled by default	%	Read
AI	360	OUTPUT3 DSP FORM	Modbus 403418; not polled by default		Read
AI	361	OUTPUT3 UNIT	Modbus 403419; not polled by default	mA	Read
AI	362	OUTPUT3 MIN	Modbus 403420; not polled by default	mA	Read
AI	363	OUTPUT3 MAX	Modbus 403421; not polled by default	mA	Read
AI	364	SENSOR TYPE	Modbus 403501; not polled by default		Read
AI	365	INPUT SELECTION	Modbus 403502; not polled by default		Read
AI	366	ALARM LIMIT	Modbus 403503; not polled by default	°C	Read
AI	367	FAULT LIMIT	Modbus 403504; not polled by default	°C	Read
AI	368	TIMERS ENABLE	Modbus 403601; not polled by default		Read
AI	369	START TIME 1	Modbus 403602; not polled by default		Read
AI	370	STOP TIME 1	Modbus 403603; not polled by default		Read
AI	371	START DAY 1	Modbus 403604; not polled by default		Read
AI	372	STOP DAY 1	Modbus 403605; not polled by default		Read
AI	373	START TIME 2	Modbus 403606; not polled by default		Read
AI	374	STOP TIME 2	Modbus 403607; not polled by default		Read
AI	375	START DAY 2	Modbus 403608; not polled by default		Read
AI	376	STOP DAY 2	Modbus 403609; not polled by default		Read
AI	377	START TIME 3	Modbus 403610; not polled by default		Read
AI	378	STOP TIME 3	Modbus 403611; not polled by default		Read
AI	379	START DAY 3	Modbus 403612; not polled by default		Read
AI	380	STOP DAY 3	Modbus 403613; not polled by default		Read
AI	381	START TIME 4	Modbus 403614; not polled by default		Read
AI	382	STOP TIME 4	Modbus 403615; not polled by default		Read
AI	383	START DAY 4	Modbus 403616; not polled by default		Read
AI	384	STOP DAY 4	Modbus 403617; not polled by default		Read
AI	385	BOOSTER SEL	Modbus 403622; not polled by default		Read
AI	386	BOOSTER TIME	Modbus 403623; not polled by default		Read
AI	387	TIMED FUNC 1 SRC	Modbus 403626; not polled by default		Read
AI	388	TIMED FUNC 2 SRC	Modbus 403627; not polled by default		Read
AI	389	TIMED FUNC 3 SRC	Modbus 403628; not polled by default		Read
AI	390	TIMED FUNC 4 SRC	Modbus 403629; not polled by default		Read
AI	391	USER LOAD C MODE	Modbus 403701; not polled by default		Read
AI	392	USER LOAD C FUNC	Modbus 403702; not polled by default		Read
AI	393	USER LOAD C TIME	Modbus 403703; not polled by default	s	Read
AI	394	LOAD FREQ 1	Modbus 403704; not polled by default	Hz	Read
AI	395	LOAD TORQ LOW 1	Modbus 403705; not polled by default	%	Read
AI	396	LOAD TORQ HIGH 1	Modbus 403706; not polled by default	%	Read
AI	397	LOAD FREQ 2	Modbus 403707; not polled by default	Hz	Read
AI	398	LOAD TORQ LOW 2	Modbus 403708; not polled by default	%	Read
AI	399	LOAD TORQ HIGH 2	Modbus 403709; not polled by default	%	Read
AI	400	LOAD FREQ 3	Modbus 403710; not polled by default	Hz	Read
AI	401	LOAD TORQ LOW 3	Modbus 403711; not polled by default	%	Read
AI	402	LOAD TORQ HIGH 3	Modbus 403712; not polled by default	%	Read
AI	403	LOAD FREQ 4	Modbus 403713; not polled by default	Hz	Read
AI	404	LOAD TORQ LOW 4	Modbus 403714; not polled by default	%	Read
AI	405	LOAD TORQ HIGH 4	Modbus 403715; not polled by default	%	Read
AI	406	LOAD FREQ 5	Modbus 403716; not polled by default	Hz	Read
AI	407	LOAD TORQ LOW 5	Modbus 403717; not polled by default	%	Read
AI	408	LOAD TORQ HIGH 5	Modbus 403718; not polled by default	%	Read
AI	409	GAIN	Modbus 404001; not polled by default		Read
AI	410	INTEGRATION TIME	Modbus 404002; not polled by default	s	Read
AI	411	DERIVATION TIME	Modbus 404003; not polled by default	s	Read
AI	412	PID DERIV FILTER	Modbus 404004; not polled by default	s	Read
AI	413	ERROR VALUE INV	Modbus 404005; not polled by default		Read
AI	414	UNITS	Modbus 404006; not polled by default	%	Read
AI	415	UNIT SCALE	Modbus 404007; not polled by default		Read
AI	416	0% VALUE	Modbus 404008; not polled by default	%	Read
AI	417	100% VALUE	Modbus 404009; not polled by default	%	Read
AI	418	SET POINT SEL	Modbus 404010; not polled by default		Read
AI	419	INTERNAL SETPNT	Modbus 404011; not polled by default	%	Read
AI	420	SETPOINT MIN	Modbus 404012; not polled by default	%	Read
AI	421	SETPOINT MAX	Modbus 404013; not polled by default	%	Read
AI	422	FBK SEL	Modbus 404014; not polled by default		Read
AI	423	FBK MULTIPLIER	Modbus 404015; not polled by default		Read
AI	424	ACT1 INPUT	Modbus 404016; not polled by default		Read
AI	425	ACT2 INPUT	Modbus 404017; not polled by default		Read
AI	426	ACT1 MINIMUM	Modbus 404018; not polled by default	%	Read
AI	427	ACT1 MAXIMUM	Modbus 404019; not polled by default	%	Read
AI	428	ACT2 MINIMUM	Modbus 404020; not polled by default	%	Read
AI	429	ACT2 MAXIMUM	Modbus 404021; not polled by default	%	Read
AI	430	SLEEP SELECTION	Modbus 404022; not polled by default		Read
AI	431	PID SLEEP LEVEL	Modbus 404023; not polled by default	rpm	Read
AI	432	PID SLEEP DELAY	Modbus 404024; not polled by default	s	Read
AI	433	WAKE-UP DEV	Modbus 404025; not polled by default	%	Read
AI	434	WAKE-UP DELAY	Modbus 404026; not polled by default	s	Read
AI	435	PID 1 PARAM SET	Modbus 404027; not polled by default		Read
AI	436	GAIN	Modbus 404101; not polled by default		Read
AI	437	INTEGRATION TIME	Modbus 404102; not polled by default	s	Read
AI	438	DERIVATION TIME	Modbus 404103; not polled by default	s	Read
AI	439	PID DERIV FILTER	Modbus 404104; not polled by default	s	Read
AI	440	ERROR VALUE INV	Modbus 404105; not polled by default	s	Read
AI	441	UNITS	Modbus 404106; not polled by default	%	Read
AI	442	UNIT SCALE	Modbus 404107; not polled by default		Read
AI	443	0% VALUE	Modbus 404108; not polled by default	%	Read
AI	444	100% VALUE	Modbus 404109; not polled by default	%	Read
AI	445	SET POINT SEL	Modbus 404110; not polled by default		Read
AI	446	INTERNAL SETPNT	Modbus 404111; not polled by default	%	Read
AI	447	SETPOINT MIN	Modbus 404112; not polled by default	%	Read
AI	448	SETPOINT MAX	Modbus 404113; not polled by default	%	Read
AI	449	FBK SEL	Modbus 404114; not polled by default		Read
AI	450	FBK MULTIPLIER	Modbus 404115; not polled by default		Read
AI	451	ACT1 INPUT	Modbus 404116; not polled by default		Read
AI	452	ACT2 INPUT	Modbus 404117; not polled by default		Read
AI	453	ACT1 MINIMUM	Modbus 404118; not polled by default	%	Read
AI	454	ACT1 MAXIMUM	Modbus 404119; not polled by default	%	Read
AI	455	ACT2 MINIMUM	Modbus 404120; not polled by default	%	Read
AI	456	ACT2 MAXIMUM	Modbus 404121; not polled by default	%	Read
AI	457	SLEEP SELECTION	Modbus 404122; not polled by default		Read
AI	458	PID SLEEP LEVEL	Modbus 404123; not polled by default	rpm	Read
AI	459	PID SLEEP DELAY	Modbus 404124; not polled by default	s	Read
AI	460	WAKE-UP DEV	Modbus 404125; not polled by default	%	Read
AI	461	WAKE-UP DELAY	Modbus 404126; not polled by default	s	Read
AI	462	GAIN	Modbus 404201; not polled by default		Read
AI	463	INTEGRATION TIME	Modbus 404202; not polled by default	s	Read
AI	464	DERIVATION TIME	Modbus 404203; not polled by default	s	Read
AI	465	PID DERIV FILTER	Modbus 404204; not polled by default	s	Read
AI	466	ERROR VALUE INV	Modbus 404205; not polled by default		Read
AI	467	UNITS	Modbus 404206; not polled by default	%	Read
AI	468	UNIT SCALE	Modbus 404207; not polled by default		Read
AI	469	0% VALUE	Modbus 404208; not polled by default	%	Read
AI	470	100% VALUE	Modbus 404209; not polled by default	%	Read
AI	471	SET POINT SEL	Modbus 404210; not polled by default		Read
AI	472	INTERNAL SETPNT	Modbus 404211; not polled by default	%	Read
AI	473	SETPOINT MIN	Modbus 404212; not polled by default	%	Read
AI	474	SETPOINT MAX	Modbus 404213; not polled by default	%	Read
AI	475	FBK SEL	Modbus 404214; not polled by default		Read
AI	476	FBK MULTIPLIER	Modbus 404215; not polled by default		Read
AI	477	ACT1 INPUT	Modbus 404216; not polled by default		Read
AI	478	ACT2 INPUT	Modbus 404217; not polled by default		Read
AI	479	ACT1 MINIMUM	Modbus 404218; not polled by default	%	Read
AI	480	ACT1 MAXIMUM	Modbus 404219; not polled by default	%	Read
AI	481	ACT2 MINIMUM	Modbus 404220; not polled by default	%	Read
AI	482	ACT2 MAXIMUM	Modbus 404221; not polled by default	%	Read
AI	483	ACTIVATE	Modbus 404228; not polled by default		Read
AI	484	OFFSET	Modbus 404229; not polled by default	%	Read
AI	485	TRIM MODE	Modbus 404230; not polled by default		Read
AI	486	TRIM SCALE	Modbus 404231; not polled by default	%	Read
AI	487	CORRECTION SRC	Modbus 404232; not polled by default		Read
AI	488	ENERGY PRICE	Modbus 404502; not polled by default		Read
AI	489	CO2 CONV FACTOR	Modbus 404507; not polled by default	MWh	Read
AI	490	PUMP POWER	Modbus 404508; not polled by default	%	Read
AI	491	ENERGY RESET	Modbus 404509; not polled by default		Read
AI	492	FBA TYPE	Modbus 405101; not polled by default		Read
AI	493	FB PAR 02	Modbus 405102; not polled by default		Read
AI	494	FB PAR 03	Modbus 405103; not polled by default		Read
AI	495	FB PAR 04	Modbus 405104; not polled by default		Read
AI	496	FB PAR 05	Modbus 405105; not polled by default		Read
AI	497	FB PAR 06	Modbus 405106; not polled by default		Read
AI	498	FB PAR 07	Modbus 405107; not polled by default		Read
AI	499	FB PAR 08	Modbus 405108; not polled by default		Read
AI	500	FB PAR 09	Modbus 405109; not polled by default		Read
AI	501	FB PAR 10	Modbus 405110; not polled by default		Read
AI	502	FB PAR 11	Modbus 405111; not polled by default		Read
AI	503	FB PAR 12	Modbus 405112; not polled by default		Read
AI	504	FB PAR 13	Modbus 405113; not polled by default		Read
AI	505	FB PAR 14	Modbus 405114; not polled by default		Read
AI	506	FB PAR 15	Modbus 405115; not polled by default		Read
AI	507	FB PAR 16	Modbus 405116; not polled by default		Read
AI	508	FB PAR 17	Modbus 405117; not polled by default		Read
AI	509	FB PAR 18	Modbus 405118; not polled by default		Read
AI	510	FB PAR 19	Modbus 405119; not polled by default		Read
AI	511	FB PAR 20	Modbus 405120; not polled by default		Read
AI	512	FB PAR 21	Modbus 405121; not polled by default		Read
AI	513	FB PAR 22	Modbus 405122; not polled by default		Read
AI	514	FB PAR 23	Modbus 405123; not polled by default		Read
AI	515	FB PAR 24	Modbus 405124; not polled by default		Read
AI	516	FB PAR 25	Modbus 405125; not polled by default		Read
AI	517	FB PAR 26	Modbus 405126; not polled by default		Read
AI	518	FBA PAR REFRESH	Modbus 405127; not polled by default		Read
AI	519	FILE CPI FW REV	Modbus 405128; not polled by default		Read
AI	520	FILE CONFIG ID	Modbus 405129; not polled by default		Read
AI	521	FILE CONFIG REV	Modbus 405130; not polled by default		Read
AI	522	FBA STATUS	Modbus 405131; not polled by default		Read
AI	523	FBA CPI FW REV	Modbus 405132; not polled by default		Read
AI	524	FBA APPL FW REV	Modbus 405133; not polled by default		Read
AI	525	STATION ID	Modbus 405201; not polled by default		Read
AI	526	BAUD RATE	Modbus 405202; not polled by default		Read
AI	527	PARITY	Modbus 405203; not polled by default		Read
AI	528	OK MESSAGES	Modbus 405204; not polled by default		Read
AI	529	PARITY ERRORS	Modbus 405205; not polled by default		Read
AI	530	FRAME ERRORS	Modbus 405206; not polled by default		Read
AI	531	BUFFER OVERRUNS	Modbus 405207; not polled by default		Read
AI	532	CRC ERRORS	Modbus 405208; not polled by default		Read
AI	533	EFB PROTOCOL ID	Modbus 405301; not polled by default		Read
AI	534	EFB STATION ID	Modbus 405302; not polled by default		Read
AI	535	EFB BAUD RATE	Modbus 405303; not polled by default		Read
AI	536	EFB PARITY	Modbus 405304; not polled by default		Read
AI	537	EFB CTRL PROFILE	Modbus 405305; not polled by default		Read
AI	538	EFB OK MESSAGES	Modbus 405306; not polled by default		Read
AI	539	EFB CRC ERRORS	Modbus 405307; not polled by default		Read
AI	540	EFB UART ERRORS	Modbus 405308; not polled by default		Read
AI	541	EFB STATUS	Modbus 405309; not polled by default		Read
AI	542	EFB PAR 10	Modbus 405310; not polled by default		Read
AI	543	EFB PAR 11	Modbus 405311; not polled by default		Read
AI	544	EFB PAR 12	Modbus 405312; not polled by default		Read
AI	545	EFB PAR 13	Modbus 405313; not polled by default		Read
AI	546	EFB PAR 14	Modbus 405314; not polled by default		Read
AI	547	EFB PAR 15	Modbus 405315; not polled by default		Read
AI	548	EFB PAR 16	Modbus 405316; not polled by default		Read
AI	549	EFB PAR 17	Modbus 405317; not polled by default		Read
AI	550	EFB PAR 18	Modbus 405318; not polled by default		Read
AI	551	EFB PAR 19	Modbus 405319; not polled by default		Read
AI	552	EFB PAR 20	Modbus 405320; not polled by default		Read
AI	553	PVL SIGNAL	Modbus 406401; not polled by default	Hz	Read
AI	554	PVL FILTER TIME	Modbus 406402; not polled by default	s	Read
AI	555	LOGGERS RESET	Modbus 406403; not polled by default		Read
AI	556	AL2 SIGNAL	Modbus 406404; not polled by default	Hz	Read
AI	557	AL2 SIGNAL BASE	Modbus 406405; not polled by default	Hz	Read
AI	558	PEAK VALUE	Modbus 406406; not polled by default		Read
AI	559	PEAK TIME 1	Modbus 406407; not polled by default		Read
AI	560	PEAK TIME 2	Modbus 406408; not polled by default		Read
AI	561	CURRENT AT PEAK	Modbus 406409; not polled by default	A	Read
AI	562	UDC AT PEAK	Modbus 406410; not polled by default	V	Read
AI	563	FREQ AT PEAK	Modbus 406411; not polled by default	Hz	Read
AI	564	TIME OF RESET 1	Modbus 406412; not polled by default		Read
AI	565	TIME OF RESET 2	Modbus 406413; not polled by default		Read
AI	566	AL1RANGE0TO10	Modbus 406414; not polled by default	%	Read
AI	567	AL1RANGE10TO20	Modbus 406415; not polled by default	%	Read
AI	568	AL1RANGE20TO30	Modbus 406416; not polled by default	%	Read
AI	569	AL1RANGE30TO40	Modbus 406417; not polled by default	%	Read
AI	570	AL1RANGE40TO50	Modbus 406418; not polled by default	%	Read
AI	571	AL1RANGE50TO60	Modbus 406419; not polled by default	%	Read
AI	572	AL1RANGE60TO70	Modbus 406420; not polled by default	%	Read
AI	573	AL1RANGE70TO80	Modbus 406421; not polled by default	%	Read
AI	574	AL1RANGE80TO90	Modbus 406422; not polled by default	%	Read
AI	575	AL1RANGE90TO	Modbus 406423; not polled by default	%	Read
AI	576	AL2RANGE0TO10	Modbus 406424; not polled by default	%	Read
AI	577	AL2RANGE10TO20	Modbus 406425; not polled by default	%	Read
AI	578	AL2RANGE20TO30	Modbus 406426; not polled by default	%	Read
AI	579	AL2RANGE30TO40	Modbus 406427; not polled by default	%	Read
AI	580	AL2RANGE40TO50	Modbus 406428; not polled by default	%	Read
AI	581	AL2RANGE50TO60	Modbus 406429; not polled by default	%	Read
AI	582	AL2RANGE60TO70	Modbus 406430; not polled by default	%	Read
AI	583	AL2RANGE70TO80	Modbus 406431; not polled by default	%	Read
AI	584	AL2RANGE80TO90	Modbus 406432; not polled by default	%	Read
AI	585	AL2RANGE90TO	Modbus 406433; not polled by default	%	Read
AI	586	REFERENCE STEP 1	Modbus 408103; not polled by default	%	Read
AI	587	REFERENCE STEP 2	Modbus 408104; not polled by default	%	Read
AI	588	REFERENCE STEP 3	Modbus 408105; not polled by default	%	Read
AI	589	START FREQ 1	Modbus 408109; not polled by default	Hz	Read
AI	590	START FREQ 2	Modbus 408110; not polled by default	Hz	Read
AI	591	START FREQ 3	Modbus 408111; not polled by default	Hz	Read
AI	592	LOW FREQ 1	Modbus 408112; not polled by default	Hz	Read
AI	593	LOW FREQ 2	Modbus 408113; not polled by default	Hz	Read
AI	594	LOW FREQ 3	Modbus 408114; not polled by default	Hz	Read
AI	595	AUX MOT START D	Modbus 408115; not polled by default	s	Read
AI	596	AUX MOT STOP D	Modbus 408116; not polled by default	s	Read
AI	597	NR OF AUX MOT	Modbus 408117; not polled by default		Read
AI	598	AUTOCHNG INTERV	Modbus 408118; not polled by default	h	Read
AI	599	AUTOCHNG LEVEL	Modbus 408119; not polled by default	%	Read
AI	600	INTERLOCKS	Modbus 408120; not polled by default		Read
AI	601	REG BYPASS CTRL	Modbus 408121; not polled by default		Read
AI	602	PFA START DELAY	Modbus 408122; not polled by default	s	Read
AI	603	PFA ENABLE	Modbus 408123; not polled by default		Read
AI	604	ACC IN AUX STOP	Modbus 408124; not polled by default	s	Read
AI	605	DEC IN AUX START	Modbus 408125; not polled by default	s	Read
AI	606	TMED AUTOCHNG	Modbus 408126; not polled by default		Read
AI	607	MOTORS	Modbus 408127; not polled by default		Read
AI	608	AUX START ORDER	Modbus 408128; not polled by default		Read
AI	609	COMM PROT SEL	Modbus 409802; not polled by default		Read

Object ID lookup: Contemporary Controls BASgatewayLX ABB ACH550 DCU point IDs by name

BI1STOP
BI2START
BI3REVERSE
BI4LOCAL
BI5RESET
BI6EXT2
BI7RUN_DISABLE
BI8STPMODE_R
BI9STPMODE_EM
BI10STPMODE_C
BI11RAMP_2
BI12RAMP_OUT_0
BI13RAMP_HOLD
BI14RAMP_IN_0
BI15REQ_LOCALLOCK
BI16TORQLIM2
BI17FBLOCAL_CTL
BI18FBLOCAL_REF
BI19START_DISABLE1
BI20START_DISABLE2
BI21Relay Output 1
BI22Relay Output 2
BI23Relay Output 3
BI24Relay Output 4
BI25Relay Output 5
BI26Relay Output 6
BI27READY
BI28ENABLED
BI29STARTED
BI30RUNNING
BI31ZERO_SPEED
BI32ACCELERATE
BI33DECELERATE
BI34AT_SETPOINT
BI35LIMIT
BI36SUPERVISION
BI37REV_REF
BI38REV_ACT
BI39PANEL_LOCAL
BI40FIELDBUS_LOCAL
BI41EXT2_ACT
BI42FAULT
BI43ALARM
BI44REQ_MAINT
BI45DIRLOCK
BI46LOCALLOCK
BI47CTL_MODE
BI48REQ_CTL
BI49REQ_REF1
BI50REQ_REF2
BI51REQ_REF2EXT
BI52ACK_STARTINH
BI53ACK_OFF_ILCK
BI54DI1
BI55DI2
BI56DI3
BI57DI4
BI58DI5
BI59DI6
AI60AI1
AI61AI2
AO62CONTROL WORD
AO63Reference 1
AO64Reference 2
AI65STATUS WORD
AI66Actual 1
AI67Actual 2
AI68Actual 3
AI69Actual 4
AI70Actual 5
AI71Actual 6
AI72Actual 7
AI73Actual 8
AO74ACH550 CONTROL WORD LSW
AI75ACH550 CONTROL WORD MSW
AI76ACH550 STATUS WORD LSW
AI77ACH550 STATUS WORD MSW
AI78LANGUAGE
AI79APPLIC MACRO
AI80MOTOR CTRL MODE
AI81MOTOR NOM VOLT
AI82MOTOR NOM CURR
AI83MOTOR NOM FREQ
AI84MOTOR NOM SPEED
AI85MOTOR NOM POWER
AI86ID RUN
AI87MOTOR COSPHI
AI88SPEED DIR
AI89SPEED
AI90OUTPUT FREQ
AI91CURRENT
AI92TORQUE
AI93POWER
AI94DC BUS VOLTAGE
AI95OUTPUT VOLTAGE
AI96DRIVE TEMP
AI97EXTERNAL REF 1
AI98EXTERNAL REF 2
AI99CTRL LOCATION
AI100RUN TIME (R)
AI101KWH COUNTER (R)
AI102APPL BLK OUTPUT
AI103DI 1-3 STATUS
AI104DI 4-6 STATUS
AI105AI 1
AI106AI 2
AI107RO 1-3 STATUS
AI108RO 4-6 STATUS
AI109AO 1
AI110AO 2
AI111PID 1 OUTPUT
AI112PID 2 OUTPUT
AI113PID 1 SETPNT
AI114PID 2 SETPNT
AI115PID 1 FBK
AI116PID 2 FBK
AI117PID 1 DEVIATION
AI118PID 2 DEVIATION
AI119COMM RO WORD
AI120COMM VALUE 1
AI121COMM VALUE 2
AI122PROCESS VAR 1
AI123PROCESS VAR 2
AI124PROCESS VAR 3
AI125RUN TIME
AI126MWH COUNTER
AI127REVOLUTION CNTR
AI128DRIVE ON TIME HI
AI129DRIVE ON TIME LO
AI130MOTOR TEMP
AI131CB TEMP
AI132MOT THERM STRESS
AI133PID COMM VALUE 1
AI134PID COMM VALUE 2
AI135SAVED KWH
AI136SAVED MWH
AI137SAVED AMOUNT 1
AI138SAVED AMOUNT 2
AI139SAVED CO2
AI140FB CMD WORD 1
AI141FB CMD WORD 2
AI142FB STS WORD 1
AI143FB STS WORD 2
AI144FAULT WORD 1
AI145FAULT WORD 2
AI146FAULT WORD 3
AI147ALARM WORD 1
AI148ALARM WORD 2
AI149LAST FAULT
AI150FAULT TIME 1
AI151FAULT TIME 2
AI152SPEED AT FLT
AI153FREQ AT FLT
AI154VOLTAGE AT FLT
AI155CURRENT AT FLT
AI156TORQUE AT FLT
AI157STATUS AT FLT
AI158DI 1-3 AT FLT
AI159DI 4-6 AT FLT
AI160PREVIOUS FAULT 1
AI161PREVIOUS FAULT 2
AI162EXT1 COMMANDS
AI163EXT2 COMMANDS
AI164DIRECTION
AI165KEYPAD REF SEL
AI166EXT1/EXT2 SEL
AI167REF1 SELECT
AI168REF1 MIN
AI169REF1 MAX
AI170REF2 SELECT
AI171REF2 MIN
AI172REF2 MAX
AI173CONST SPEED SEL
AI174CONST SPEED 1
AI175CONST SPEED 2
AI176CONST SPEED 3
AI177CONST SPEED 4
AI178CONST SPEED 5
AI179CONST SPEED 6
AI180CONST SPEED 7
AI181TIMED MODE SEL
AI182MINIMUM AI1
AI183MAXIMUM AI1
AI184FILTER AI1
AI185MINIMUM AI2
AI186MAXIMUM AI2
AI187FILTER AI2
AI188RELAY OUTPUT 1
AI189RELAY OUTPUT 2
AI190RELAY OUTPUT 3
AI191RO 1 ON DELAY
AI192RO 1 OFF DELAY
AI193RO 2 ON DELAY
AI194RO 2 OFF DELAY
AI195RO 3 ON DELAY
AI196RO 3 OFF DELAY
AI197RELAY OUTPUT 4
AI198RELAY OUTPUT 5
AI199RELAY OUTPUT 6
AI200RO 4 ON DELAY
AI201RO 4 OFF DELAY
AI202RO 5 ON DELAY
AI203RO 5 OFF DELAY
AI204RO 6 ON DELAY
AI205RO 6 OFF DELAY
AI206AO1 CONTENT SEL
AI207AO1 CONTENT MIN
AI208AO1 CONTENT MAX
AI209MINIMUM AO1
AI210MAXIMUM AO1
AI211FILTER AO1
AI212AO2 CONTENT SEL
AI213AO2 CONTENT MIN
AI214AO2 CONTENT MAX
AI215MINIMUM AO2
AI216MAXIMUM AO2
AI217FILTER AO2
AI218RUN ENABLE
AI219PARAMETER LOCK
AI220PASS CODE
AI221FAULT RESET sEL
AI222USER PAR SET CHG
AI223LOCAL LOCK
AI224PARAM SAVE
AI225START ENABLE 1
AI226START ENABLE 2
AI227DISPLAY ALARMS
AI228PARAMETER VIEW
AI229FAN CONTROL
AI230FAULT RESET
AI231OVERRIDE SEL
AI232OVERRIDE FREQ
AI233OVERRIDE SPEED
AI234OVERR PASS CODE
AI235OVERRIDE
AI236OVERRIDE DIR
AI237OVERRIDE REF
AI238MINIMUM SPEED
AI239MAXIMUM SPEED
AI240MAX CURRENT
AI241UNDERVOLT CTRL
AI242MINIMUM FREQ
AI243MAXIMUM FREQ
AI244MIN TORQUE SEL
AI245MAX TORQUE SEL
AI246MIN TORQUE 1
AI247MIN TORQUE 2
AI248MAX TORQUE 1
AI249MAX TORQUE 2
AI250START FUNCTION
AI251STOP FUNCTION
AI252DC MAGN TIME
AI253DC HOLD CTL
AI254DC HOLD SPEED
AI255DC CURR REF
AI256DC BRAKE TIME
AI257START INHIBIT
AI258EMERG STOP SEL
AI259TORQ BOOST CURR
AI260START DELAY
AI261ACC/DEC 1/2 SEL
AI262ACCELER TIME 1
AI263DECELER TIME 1
AI264RAMP SHAPE 1
AI265ACCELER TIME 2
AI266DECELER TIME 2
AI267RAMP SHAPE 2
AI268EMERG DEC TIME
AI269RAMP INPUT 0
AI270PROP GAIN
AI271INTEGRATION TIME
AI272DERIVATION TIME
AI273ACC COMPENSATION
AI274AUTOTUNE RUN
AI275CRIT SPEED SEL
AI276CRIT SPEED 1 LO
AI277CRIT SPEED 1 HI
AI278CRIT SPEED 2 LO
AI279CRIT SPEED 2 HI
AI280CRIT SPEED 3 LO
AI281CRIT SPEED 3 HI
AI282FLUX OPT ENABLE
AI283FLUX BRAKING
AI284IR COMP VOLT
AI285IR COMP FREQ
AI286U/F RATIO
AI287SWITCHING FREQ
AI288SWITCH FREQ CTRL
AI289SLIP COMP RATIO
AI290NOISE SMOOTHING
AI291DC STABILIZER
AI292OVERMODULATION
AI293COOLING FAN TRIG
AI294COOLING FAN ACT
AI295REVOLUTION TRIG
AI296REVOLUTION ACT
AI297RUN TIME TRIG
AI298RUN TIME ACT
AI299USER MWh TRIG
AI300USER MWh ACT
AI301AI<MIN FUNCTION
AI302PANEL COMM ERR
AI303EXTERNAL FAULT 1
AI304EXTERNAL FAULT 2
AI305MOT THERM PROT
AI306MOT THERM TIME
AI307MOT LOAD CURVE
AI308ZERO SPEED LOAD
AI309BREAK POINT FREQ
AI310STALL FUNCTION
AI311STALL FREQUENCY
AI312STALL TIME
AI313EARTH FAULT
AI314COMM FAULT FUNC
AI315COMM FAULT TIME
AI316AI1 FAULT LIMIT
AI317AI2 FAULT LIMIT
AI318WIRING FAULT
AI319CB TEMP FAULT
AI320EARTH FAULT LVL
AI321NUMBER OF TRIALS
AI322TRIAL TIME
AI323DELAY TIME
AI324AR OVERCURRENT
AI325AR OVERVOLTAGE
AI326AR UNDERVOLTAGE
AI327AR AI<MIN
AI328AR EXTERNAL FLT
AI329SUPERV 1 PARAM
AI330SUPERV 1 LIM LO
AI331SUPERV 1 LIM HI
AI332SUPERV 2 PARAM
AI333SUPERV 2 LIM LO
AI334SUPERV 2 LIM HI
AI335SUPERV 3 PARAM
AI336SUPERV 3 LIM LO
AI337SUPERV 3 LIM HI
AI338FIRMWARE
AI339LOADING PACKAGE
AI340TEST DATE
AI341DRIVE RATING
AI342PARAMETER TABLE
AI343SIGNAL1 PARAM
AI344SIGNAL1 MIN
AI345SIGNAL1 MAX
AI346OUTPUT1 DSP FORM
AI347OUTPUT1 UNIT
AI348OUTPUT1 MIN
AI349OUTPUT1 MAX
AI350SIGNAL2 PARAM
AI351SIGNAL2 MIN
AI352SIGNAL2 MAX
AI353OUTPUT2 DSP FORM
AI354OUTPUT2 UNIT
AI355OUTPUT2 MIN
AI356OUTPUT2 MAX
AI357SIGNAL3 PARAM
AI358SIGNAL3 MIN
AI359SIGNAL3 MAX
AI360OUTPUT3 DSP FORM
AI361OUTPUT3 UNIT
AI362OUTPUT3 MIN
AI363OUTPUT3 MAX
AI364SENSOR TYPE
AI365INPUT SELECTION
AI366ALARM LIMIT
AI367FAULT LIMIT
AI368TIMERS ENABLE
AI369START TIME 1
AI370STOP TIME 1
AI371START DAY 1
AI372STOP DAY 1
AI373START TIME 2
AI374STOP TIME 2
AI375START DAY 2
AI376STOP DAY 2
AI377START TIME 3
AI378STOP TIME 3
AI379START DAY 3
AI380STOP DAY 3
AI381START TIME 4
AI382STOP TIME 4
AI383START DAY 4
AI384STOP DAY 4
AI385BOOSTER SEL
AI386BOOSTER TIME
AI387TIMED FUNC 1 SRC
AI388TIMED FUNC 2 SRC
AI389TIMED FUNC 3 SRC
AI390TIMED FUNC 4 SRC
AI391USER LOAD C MODE
AI392USER LOAD C FUNC
AI393USER LOAD C TIME
AI394LOAD FREQ 1
AI395LOAD TORQ LOW 1
AI396LOAD TORQ HIGH 1
AI397LOAD FREQ 2
AI398LOAD TORQ LOW 2
AI399LOAD TORQ HIGH 2
AI400LOAD FREQ 3
AI401LOAD TORQ LOW 3
AI402LOAD TORQ HIGH 3
AI403LOAD FREQ 4
AI404LOAD TORQ LOW 4
AI405LOAD TORQ HIGH 4
AI406LOAD FREQ 5
AI407LOAD TORQ LOW 5
AI408LOAD TORQ HIGH 5
AI409GAIN
AI410INTEGRATION TIME
AI411DERIVATION TIME
AI412PID DERIV FILTER
AI413ERROR VALUE INV
AI414UNITS
AI415UNIT SCALE
AI4160% VALUE
AI417100% VALUE
AI418SET POINT SEL
AI419INTERNAL SETPNT
AI420SETPOINT MIN
AI421SETPOINT MAX
AI422FBK SEL
AI423FBK MULTIPLIER
AI424ACT1 INPUT
AI425ACT2 INPUT
AI426ACT1 MINIMUM
AI427ACT1 MAXIMUM
AI428ACT2 MINIMUM
AI429ACT2 MAXIMUM
AI430SLEEP SELECTION
AI431PID SLEEP LEVEL
AI432PID SLEEP DELAY
AI433WAKE-UP DEV
AI434WAKE-UP DELAY
AI435PID 1 PARAM SET
AI436GAIN
AI437INTEGRATION TIME
AI438DERIVATION TIME
AI439PID DERIV FILTER
AI440ERROR VALUE INV
AI441UNITS
AI442UNIT SCALE
AI4430% VALUE
AI444100% VALUE
AI445SET POINT SEL
AI446INTERNAL SETPNT
AI447SETPOINT MIN
AI448SETPOINT MAX
AI449FBK SEL
AI450FBK MULTIPLIER
AI451ACT1 INPUT
AI452ACT2 INPUT
AI453ACT1 MINIMUM
AI454ACT1 MAXIMUM
AI455ACT2 MINIMUM
AI456ACT2 MAXIMUM
AI457SLEEP SELECTION
AI458PID SLEEP LEVEL
AI459PID SLEEP DELAY
AI460WAKE-UP DEV
AI461WAKE-UP DELAY
AI462GAIN
AI463INTEGRATION TIME
AI464DERIVATION TIME
AI465PID DERIV FILTER
AI466ERROR VALUE INV
AI467UNITS
AI468UNIT SCALE
AI4690% VALUE
AI470100% VALUE
AI471SET POINT SEL
AI472INTERNAL SETPNT
AI473SETPOINT MIN
AI474SETPOINT MAX
AI475FBK SEL
AI476FBK MULTIPLIER
AI477ACT1 INPUT
AI478ACT2 INPUT
AI479ACT1 MINIMUM
AI480ACT1 MAXIMUM
AI481ACT2 MINIMUM
AI482ACT2 MAXIMUM
AI483ACTIVATE
AI484OFFSET
AI485TRIM MODE
AI486TRIM SCALE
AI487CORRECTION SRC
AI488ENERGY PRICE
AI489CO2 CONV FACTOR
AI490PUMP POWER
AI491ENERGY RESET
AI492FBA TYPE
AI493FB PAR 02
AI494FB PAR 03
AI495FB PAR 04
AI496FB PAR 05
AI497FB PAR 06
AI498FB PAR 07
AI499FB PAR 08
AI500FB PAR 09
AI501FB PAR 10
AI502FB PAR 11
AI503FB PAR 12
AI504FB PAR 13
AI505FB PAR 14
AI506FB PAR 15
AI507FB PAR 16
AI508FB PAR 17
AI509FB PAR 18
AI510FB PAR 19
AI511FB PAR 20
AI512FB PAR 21
AI513FB PAR 22
AI514FB PAR 23
AI515FB PAR 24
AI516FB PAR 25
AI517FB PAR 26
AI518FBA PAR REFRESH
AI519FILE CPI FW REV
AI520FILE CONFIG ID
AI521FILE CONFIG REV
AI522FBA STATUS
AI523FBA CPI FW REV
AI524FBA APPL FW REV
AI525STATION ID
AI526BAUD RATE
AI527PARITY
AI528OK MESSAGES
AI529PARITY ERRORS
AI530FRAME ERRORS
AI531BUFFER OVERRUNS
AI532CRC ERRORS
AI533EFB PROTOCOL ID
AI534EFB STATION ID
AI535EFB BAUD RATE
AI536EFB PARITY
AI537EFB CTRL PROFILE
AI538EFB OK MESSAGES
AI539EFB CRC ERRORS
AI540EFB UART ERRORS
AI541EFB STATUS
AI542EFB PAR 10
AI543EFB PAR 11
AI544EFB PAR 12
AI545EFB PAR 13
AI546EFB PAR 14
AI547EFB PAR 15
AI548EFB PAR 16
AI549EFB PAR 17
AI550EFB PAR 18
AI551EFB PAR 19
AI552EFB PAR 20
AI553PVL SIGNAL
AI554PVL FILTER TIME
AI555LOGGERS RESET
AI556AL2 SIGNAL
AI557AL2 SIGNAL BASE
AI558PEAK VALUE
AI559PEAK TIME 1
AI560PEAK TIME 2
AI561CURRENT AT PEAK
AI562UDC AT PEAK
AI563FREQ AT PEAK
AI564TIME OF RESET 1
AI565TIME OF RESET 2
AI566AL1RANGE0TO10
AI567AL1RANGE10TO20
AI568AL1RANGE20TO30
AI569AL1RANGE30TO40
AI570AL1RANGE40TO50
AI571AL1RANGE50TO60
AI572AL1RANGE60TO70
AI573AL1RANGE70TO80
AI574AL1RANGE80TO90
AI575AL1RANGE90TO
AI576AL2RANGE0TO10
AI577AL2RANGE10TO20
AI578AL2RANGE20TO30
AI579AL2RANGE30TO40
AI580AL2RANGE40TO50
AI581AL2RANGE50TO60
AI582AL2RANGE60TO70
AI583AL2RANGE70TO80
AI584AL2RANGE80TO90
AI585AL2RANGE90TO
AI586REFERENCE STEP 1
AI587REFERENCE STEP 2
AI588REFERENCE STEP 3
AI589START FREQ 1
AI590START FREQ 2
AI591START FREQ 3
AI592LOW FREQ 1
AI593LOW FREQ 2
AI594LOW FREQ 3
AI595AUX MOT START D
AI596AUX MOT STOP D
AI597NR OF AUX MOT
AI598AUTOCHNG INTERV
AI599AUTOCHNG LEVEL
AI600INTERLOCKS
AI601REG BYPASS CTRL
AI602PFA START DELAY
AI603PFA ENABLE
AI604ACC IN AUX STOP
AI605DEC IN AUX START
AI606TMED AUTOCHNG
AI607MOTORS
AI608AUX START ORDER
AI609COMM PROT SEL

Integration notes

Built from Contemporary Controls' BASgatewayLX Modbus device profile ABB_Drive_DCU_5305_is_1_a_LX.csv; the profile maps the registers in the ACH550 user's manual (3AUA0000081823), embedded fieldbus section (https://www.ccontrols.com/support/dp/3AUA0000081823_REVC.pdf).
Object instances are the ones this profile assigns when it is loaded into the gateway. A site that edited or rebuilt the profile may use different instances.
Only 138 of the 609 rows are flagged for polling in the profile; the rest are served only after you tick them in the gateway. Their descriptions say "not polled by default".
The CSV has no read/write column: Analog/Binary Inputs are read-only and Analog/Binary Outputs are commandable (priority array), which is how the gateway maps them (access inferred). Descriptions give the Modbus register each object reads.
Some names appear more than once in the profile as published (INTEGRATION TIME; DERIVATION TIME; GAIN...); they are kept as printed and told apart by instance.

Check it against the live device. A points list tells you what the controller can expose; the unit in front of you may differ by firmware or installed options. This list is provided as-is for reference only and may contain mistakes — confirming it before you write, map or commission anything is up to you (terms). Easy BACnet scans a network for BACnet IP devices from an Android phone, reads every object on the ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX and exports what it actually has to Excel — free. New to BACnet? Start with what a BACnet points list is and what the object types mean.

Questions about the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX

How many BACnet points does the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX have?

This list has 609 BACnet objects: 546 analog inputs, 4 analog outputs, 59 binary inputs. The exact set on a given unit depends on its firmware, installed options and configuration.

Which Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet points are writable?

4 of the 609 objects accept a write. Points marked Command have a priority array: a write holds until it is released, so release it back to automatic when you are done. The source has no read/write column, so this is inferred from object type.

Where is the official Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet documentation?

The source is BASgatewayLX Modbus device profile ABB_Drive_DCU_5305_is_1_a (ABB_Drive_DCU_5305_is_1_a_LX.csv), published free by Contemporary Controls at https://www.ccontrols.com/support/dp/ABB_Drive_DCU_5305_is_1_a_LX.zip.

What are the minimum BACnet points to integrate the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX?

Start with AO 74 ACH550 CONTROL WORD LSW (DCU control word, low word: start/stop, reset bits); AO 63 Reference 1 (Speed reference REF1); BI 30 RUNNING (Drive running); AI 90 OUTPUT FREQ (Output frequency, Hz); AI 89 SPEED (Motor speed, rpm); AI 91 CURRENT (Motor current, A); AI 93 POWER (Output power, kW); BI 43 ALARM (Any active alarm); BI 42 FAULT (Drive tripped on a fault); AI 144 FAULT WORD 1 (Fault bits, word 1).

How do I enable BMS control of the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX?

How do I check these points on the real ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX?

Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.

More Contemporary Controls BACnet points lists

Source: BASgatewayLX Modbus device profile ABB_Drive_DCU_5305_is_1_a · ABB_Drive_DCU_5305_is_1_a_LX.csv. Object names, instances and units are reproduced as published; descriptions are our own.

Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet points list

BMS integration notes: Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX

Minimum points to map

Enable & remote start

Network setup

Watch out for

Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX BACnet objects

Integration notes

Questions about the Contemporary Controls ABB ACH550 (DCU profile, 5305 = 1) via BASgatewayLX

More Contemporary Controls BACnet points lists

Contemporary Controls ABB ACH 400 via BASgatewayLX

Contemporary Controls ABB ACH550 (ABB DRV FULL profile, 5305 = 2) via BASgatewayLX

Contemporary Controls ABB ACH550 (ABB DRV LIM profile, 5305 = 0) via BASgatewayLX

Contemporary Controls Acromag 961EN / 962EN Ethernet I/O module via BASgatewayLX

Contemporary Controls Advanced Thermal Hydronics (Hydrotherm) KN-2 / KN-4 via BASgatewayLX

Contemporary Controls AERCO BMS / BMS II Boiler Management System via BASgatewayLX

Contemporary Controls AERCO C-More Boiler Controller via BASgatewayLX

Contemporary Controls AERMEC chillers/heat pumps via AER485 interface via BASgatewayLX

Contemporary Controls ASCO 7000 Series Group 5 controller via BASgatewayLX

Contemporary Controls ASCO Power Manager Xp via BASgatewayLX

Contemporary Controls Bacharach HGM-MZ multi-zone refrigerant monitor via BASgatewayLX

Contemporary Controls BASstat BAST-121C-B2 Single Mode Thermostat

Contemporary Controls BASstat BAST-121C-BW2 Wireless Single Mode Thermostat

Contemporary Controls BASstat BAST-221C/CH-B2 Multi-Stage Thermostat

Contemporary Controls BASstat BAST-221C/CH-BW2 Wireless Multi-Stage Thermostat

Contemporary Controls BASstat BAST-321HP-B2 Heat Pump Thermostat

Contemporary Controls BASstat BAST-321HP-BW2 Wireless Heat Pump Thermostat

Contemporary Controls BASstat BAST-421C-B2 Modulating Fan Coil Thermostat

Contemporary Controls BASstat BAST-421C-BW2 Wireless Modulating Fan Coil Thermostat

Contemporary Controls BECS BECsys5 / BECsys7 / BECsysBW water chemistry controller via BASgatewayLX

Contemporary Controls Benshaw RediStart RB2 / RC2 / RX2E soft starter via BASgatewayLX

Contemporary Controls Carlo Gavazzi EM21 via BASgatewayLX

Contemporary Controls Carlo Gavazzi EM24 via BASgatewayLX

Contemporary Controls Caterpillar ATC 300+ transfer switch controller via BASgatewayLX

Contemporary Controls Caterpillar EMCP 4 generator set control via BASgatewayLX

Contemporary Controls Cleaver-Brooks Falcon (Honeywell SOLA-based) boiler control via BASgatewayLX

Contemporary Controls Crompton Instruments INTEGRA 15xx via BASgatewayLX

Contemporary Controls Cummins PowerCommand 2.x / 3.x genset control via BASgatewayLX

Contemporary Controls Cummins PowerCommand CCM-G genset monitoring via BASgatewayLX

Contemporary Controls Danfoss VLT HVAC Drive FC 102 via BASgatewayLX

Contemporary Controls E-Mon D-Mon Class 3200 / 3400 / 5000 via BASgatewayLX

Contemporary Controls E-Mon D-Mon IDR-8 / IDR-16 interval data recorder via BASgatewayLX

Contemporary Controls Eaton IQ 250 / IQ 260 via BASgatewayLX

Contemporary Controls Eaton IQ 300 via BASgatewayLX

Contemporary Controls Eaton Motor Insight overload relay via BASgatewayLX

Contemporary Controls Eaton Pow-R-Command PRC100 / Mod100 lighting panel via BASgatewayLX

Contemporary Controls Eaton Power Xpert PXM 2000 via BASgatewayLX

Contemporary Controls Eaton Powerware 9390 UPS via BASgatewayLX

Contemporary Controls Eaton RS-485 PONI (IQ product network interface) via BASgatewayLX

Contemporary Controls ebm-papst ArgusVision Dependent Boiler via BASgatewayLX

Contemporary Controls ebm-papst ArgusVision Heat Recovery Unit (Basic) via BASgatewayLX

Contemporary Controls ebm-papst ArgusVision Trio Managing Boiler via BASgatewayLX

Contemporary Controls Elevator Controls Corporation Pixel elevator controller via BASgatewayLX

Contemporary Controls Fireye PPC4000 parallel positioning control via BASgatewayLX

Contemporary Controls Fox Thermal Instruments FT2 via BASgatewayLX

Contemporary Controls GE EPM 2200 via BASgatewayLX

Contemporary Controls GE EPM 4500 multi-point submeter via BASgatewayLX

Contemporary Controls GE EPM 6000 via BASgatewayLX

Contemporary Controls GE Multilin PQMII via BASgatewayLX

Contemporary Controls GE Zenith Controls MX200 transfer switch controller via BASgatewayLX

Contemporary Controls Generac G-Panel generator control via BASgatewayLX

Contemporary Controls Generac H-100 control panel via BASgatewayLX

Contemporary Controls Harsco Patterson-Kelley NURO via BASgatewayLX

Contemporary Controls Honeywell 7800 SERIES burner control (S7800A1142 display) via BASgatewayLX

Contemporary Controls Ingersoll Rand XE-90M / XE-145M compressor controller via BASgatewayLX

Contemporary Controls Kohler Decision-Maker 550 generator controller via BASgatewayLX

Contemporary Controls Kohler MPAC 1500 transfer switch controller via BASgatewayLX

Contemporary Controls Liebert iCOM v4 (Challenger 3000, Challenger ITR, CW, Deluxe System/3, DS, DSE, PeX, HPM) via BASgatewayLX

Contemporary Controls Liebert Mini-Mate2 via BASgatewayLX

Contemporary Controls Liebert Series 600 UPS via BASgatewayLX

Contemporary Controls Liebert Table 27 units (LAM, Challenger 3000, Deluxe System/3, Himod, ICS) via BASgatewayLX

Contemporary Controls Lochinvar Armor, Knight, FTXL and Wall Mount via BASgatewayLX

Contemporary Controls Lochinvar Crest boiler via BASgatewayLX

Contemporary Controls Mitsubishi Electric 9900A UPS (Modbus TCP) via BASgatewayLX

Contemporary Controls Mitsubishi Electric AG-150 central controller via Procon Mod-IP/50 via BASgatewayLX

Contemporary Controls Mitsubishi Electric UPS 1100/2033/7011/9800/9900 via Procon Mod-IP/50 (MUCM) via BASgatewayLX

Contemporary Controls Pentair Raychem DigiTrace C910 heat-tracing controller via BASgatewayLX

Contemporary Controls PVI Industries TempTrac water heater control via BASgatewayLX

Contemporary Controls PVI Industries XR10CX controller via BASgatewayLX

Contemporary Controls Sage Metering Sage Prime SIP / SRP via BASgatewayLX