Easy BACnet- Home
- BACnet points lists
- Johnson Controls
- Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP)
Variable frequency drive (HVAC) · BACnet points list
Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) BACnet points list
Updated 6 November 2026
The VSD Series III has BACnet MS/TP on its RS-485 terminals (P12.3.1.1 RS485 Comm Set = 1) and BACnet IP on its RJ45 port (P12.4.1.9 Enable BACnet IP = 1). Both sections of the manual print the same object list: BVs for drive status, run/stop, direction, reset, control and speed source select, bypass and fire mode, digital I/O; AVs for the speed reference, limits, ramps, AnyParam access and process data in; AIs for monitors and process data out; and MVs for control mode and active fault.
This page lists 78 BACnet objects for the Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) — 29 of them writable — with each object’s type, instance number, name, engineering units and access. It is re-typed from Johnson Controls’s own free documentation, linked below.
- Manufacturer
- Johnson Controls
- Model
- Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP)
- Equipment
- Variable frequency drive (HVAC)
- Equipment type
- VFDs & pumps
- BACnet objects
- 78 (29 writable)
- Transport
- BACnet MS/TP, BACnet IP
- Firmware
- Not stated
- Also known as
- VSD Series III, Variable Speed Drive Series 3, JCI VSD3, VS3 drive, LIT-12013000
Reference only, provided as-is: verify against Johnson Controls’s current documentation and the live device before use. Not official Johnson Controls information. Terms of use.
BMS integration notes: Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP)
For MS/TP set P12.3.1.1 = 1 (BACnet MS/TP), then the baud rate, MAC address, instance number and Max Master in P12.3.3. For BACnet IP set the IP mode and static address in P12.4.1 and P12.4.1.9 = 1, then the UDP port and instance in P12.4.3. Write BV 7 and BV 8 to fieldbus control, then BV 9 run/stop and AV 0 speed reference; read BV 1, AI 1, AI 5 and BV 3.
Minimum points to map
The short list most integrators start with — enough to run the unit from a BMS. Map more as the job needs.
| Object | Name | Why | Access |
|---|---|---|---|
| BV 9 | Run/Stop CMD | Start/stop command (Run = start) | Command |
| BV 7 | Motor Ctrl source | Must be FBMotorCtrl for network run/stop | Command |
| AV 0 | Speed Reference | Speed reference, % | Command |
| BV 8 | Speed Reference Source | Must be FBSpeedRef for the network reference | Command |
| BV 11 | Reset Fault | Reset a tripped drive | Command |
| BV 1 | Run/Stop State | Running status | Read |
| AI 1 | Output Frequency | Output frequency, Hz | Read |
| AI 5 | Motor Current | Motor amps | Read |
| BV 3 | Fault State | Any active drive fault | Read |
| MV 1 | Active fault code | Active fault code | Read |
Enable & remote start
BV 7 Motor Ctrl source selects local or fieldbus (FBMotorCtrl) control of run/stop, and BV 8 Speed Reference Source selects local or fieldbus (FBSpeedRef) speed reference. MV 0 shows whether the drive is in Local (Hand), Remote or OFF.
Heartbeat & communication loss
MS/TP: Comm Timeout BACnet (P12.3.3, default 10000 ms) raises a communication error if the drive is sole master for that long. BACnet IP: BACnet IP Comm Timeout (P12.4.3, 0 = no supervision) raises a fieldbus fault after that many seconds without messages; the parameter table prints default 0, while the text says the default is 10 s. A pulled Ethernet cable faults at once. The Modbus RTU/BACnet Fault Response and BACnet IP Fault Behavior parameters choose whether the fault is raised only in fieldbus control (0, default) or in all control places (1).
Network setup
- MS/TP: P12.3.1.1 RS485 Comm Set = 1; BACnet baud rate default 38400 (9600-115200); MAC address 0-127, default 1; Max Master default 127.
- MS/TP: the instance number (0-4194302) is set in P12.3.3; its default varies by drive.
- BACnet IP: P12.4.1.1 IP Address Mode (default 1 = DHCP with AutoIP, 0 = static); static defaults 192.168.1.254 / 255.255.255.0 / gateway 192.168.1.1. A change of IP mode needs a power cycle.
- BACnet IP: P12.4.1.9 Enable BACnet IP = 1 (default 0) shows the P12.4.3 settings: UDP port (47808-47823), foreign device, BBMD IP/port, registration interval (default 10 s) and instance number.
- Segmentation is not supported; the drive is a B-ASC.
Watch out for
- BACnet IP and BACnet MS/TP cannot run at the same time.
- BV 28 Force Bypass and BV 29 Fire Mode are commandable over BACnet.
- The manual's MS/TP parameter table is laid out unclearly; confirm parameter codes on the keypad (Main Menu > Parameter > Communication > RS485 Bus).
Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) BACnet objects
Type: AI, AO, AV, BI, BO, BV, MI/MO/MV (multi-state) · Access: Read read-only, Write writable, Command writable with a priority array.
| Description | States | |||||
|---|---|---|---|---|---|---|
| BV | 0 | Ready State | Indicates whether the drive is ready or not | Read | Inactive/Active: Not Ready/Ready | |
| BVmin | 1 | Run/Stop State | Indicates whether the drive is running or stopped | Read | Inactive/Active: Stop/Run | |
| BV | 2 | Fwd/Rev State | Indicates the rotation direction of motor | Read | Inactive/Active: Fwd/Rev | |
| BVmin | 3 | Fault State | Indicates if a fault is active | Read | Inactive/Active: OK/Fault | |
| BV | 4 | Warning State | Indicates if a warning is active | Read | Inactive/Active: OK/Warning | |
| BV | 5 | At Setpoint | Ref. Frequency reached | Read | Inactive/Active: False/True | |
| BV | 6 | At Zero Speed | Motor Running at zero speed | Read | Inactive/Active: False/True | |
| BVmin | 7 | Motor Ctrl source | Command to change active source for controlling motor | Command | Inactive/Active: LocalMotorCtrl/FBMotorCtrl | |
| BVmin | 8 | Speed Reference Source | Command to change source of motor speed reference | Command | Inactive/Active: LocalSpeedRef/FBSpeedRef | |
| BVmin | 9 | Run/Stop CMD | Command to start drive | Command | Inactive/Active: Stop/Run | |
| BV | 10 | Fwd/Rev CMD | Command to change rotational direction | Command | Inactive/Active: Fwd/Rev | |
| BVmin | 11 | Reset Fault | Command to reset active Fault from drive | Command | Inactive/Active: 0/Reset | |
| BV | 12 | Digital Input 1 | Digital Input 1 | Read | Inactive/Active: OFF/ON | |
| BV | 13 | Digital Input 2 | Digital Input 2 | Read | Inactive/Active: OFF/ON | |
| BV | 14 | Digital Input 3 | Digital Input 3 | Read | Inactive/Active: OFF/ON | |
| BV | 15 | Digital Input 4 | Digital Input 4 | Read | Inactive/Active: OFF/ON | |
| BV | 16 | Digital Input 5 | Digital Input 5 | Read | Inactive/Active: OFF/ON | |
| BV | 17 | Digital Input 6 | Digital Input 6 | Read | Inactive/Active: OFF/ON | |
| BV | 18 | Digital Input 7 | Digital Input 7 | Read | Inactive/Active: OFF/ON | |
| BV | 19 | Digital Input 8 | Digital Input 8 | Read | Inactive/Active: OFF/ON | |
| BV | 20 | Digital Output 1 | Digital Output 1 | Read | Inactive/Active: OFF/ON | |
| BV | 21 | Digital Output 2 | Relay 1 Output | Read | Inactive/Active: OFF/ON | |
| BV | 22 | Digital Output 3 | Relay 2 Output | Read | Inactive/Active: OFF/ON | |
| BV | 23 | Digital Output 4 | Relay 3 Output | Read | Inactive/Active: OFF/ON | |
| BV | 24 | Stop By Coast | Indicates if drive stop by coast | Command | Inactive/Active: ON/OFF | |
| BV | 25 | Stop By Ramp | Indicates if drive stop by Ramp | Command | Inactive/Active: OFF/ON | |
| BV | 26 | Belt Broken | Indicates If belt is broken | Read | Inactive/Active: OFF/ON | |
| BV | 27 | Drive Fan Failure | Indicates if Drive Fan failed | Read | Inactive/Active: OFF/ON | |
| BV | 28 | Force Bypass | Command to take Drive in Bypass Mode | Command | Inactive/Active: OFF/ON | |
| BV | 29 | Fire Mode | Enable Fire Mode | Command | Inactive/Active: OFF/ON | |
| BV | 30 | DIN 1 | Fieldbus Digital Input | Command | Inactive/Active: OFF/ON | |
| BV | 31 | DIN 2 | Fieldbus Digital Input | Command | Inactive/Active: OFF/ON | |
| BV | 32 | DIN 3 | Fieldbus Digital Input | Command | Inactive/Active: OFF/ON | |
| BV | 33 | DIN 4 | Fieldbus Digital Input | Command | Inactive/Active: OFF/ON | |
| AVmin | 0 | Speed Reference | Motor speed reference from network | % | Command | |
| AV | 1 | Current Limit | Current Limit | A | Write | |
| AV | 2 | Min Frequency | Minimum Frequency | Hz | Write | |
| AV | 3 | Maximum Frequency | Maximum Frequency | Hz | Write | |
| AV | 4 | Accel Time 1 | Acceleration Time | s | Write | |
| AV | 5 | Decel Time 1 | Deceleration Time | s | Write | |
| AV | 6 | AnyParam ID | Parameter ID number to be accessed | Write | ||
| AV | 7 | AnyParam Value | Value of parameter defined by AV6 | Write | ||
| AV | 8 | Process Data In 1 | Fieldbus Process Data In 1 | Command | ||
| AV | 9 | Process Data In 2 | Fieldbus Process Data In 2 | Command | ||
| AV | 10 | Process Data In 3 | Fieldbus Process Data In 3 | Command | ||
| AV | 11 | Process Data In 4 | Fieldbus Process Data In 4 | Command | ||
| AV | 12 | Process Data In 5 | Fieldbus Process Data In 5 | Command | ||
| AV | 13 | Process Data In 6 | Fieldbus Process Data In 6 | Command | ||
| AV | 14 | Process Data In 7 | Fieldbus Process Data In 7 | Command | ||
| AV | 15 | Process Data In 8 | Fieldbus Process Data In 8 | Command | ||
| AI | 0 | Frequency Setpoint | Frequency Setpoint | Hz | Read | |
| AImin | 1 | Output Frequency | Output Frequency | Hz | Read | |
| AI | 2 | Motor Speed | Motor Speed | rpm | Read | |
| AI | 3 | Motor Load | Motor Load | % | Read | |
| AI | 4 | Kilowatt Hours total | Kilowatt Hour Counter (Total) scaled by 1000 | kWh | Read | |
| AImin | 5 | Motor Current | Motor Current | A | Read | |
| AI | 6 | DC link Voltage | DC link Voltage | V | Read | |
| AI | 7 | Motor Voltage | Motor Voltage | V | Read | |
| AI | 8 | Unit Temperature | Heatsink Temperature | °C | Read | |
| AI | 9 | Motor Torque | In % of motor nominal Torque | % | Read | |
| AI | 10 | Operating Days | Operating Days (resettable) | days | Read | |
| AI | 11 | Operating Hours | Operating Hours (resettable) | h | Read | |
| AI | 12 | Motor Temperature | Motor Temperature | % | Read | |
| AI | 13 | Analog Input 1 | Analog Input 1 | V | Read | |
| AI | 14 | Analog Input 2 | Analog Input 2 | V | Read | |
| AI | 15 | Analog Output 1 | Analog Output 1 | V | Read | |
| AI | 16 | Analog Output 2 | Analog Output 2 | V | Read | |
| AI | 17 | Kilowatt Instantaneous | Kilowatt Instantaneous | kW | Read | |
| AI | 18 | Process Data Out 1 | Fieldbus Process Data Out 1 | Read | ||
| AI | 19 | Process Data Out 2 | Fieldbus Process Data Out 2 | Read | ||
| AI | 20 | Process Data Out 3 | Fieldbus Process Data Out 3 | Read | ||
| AI | 21 | Process Data Out 4 | Fieldbus Process Data Out 4 | Read | ||
| AI | 22 | Process Data Out 5 | Fieldbus Process Data Out 5 | Read | ||
| AI | 23 | Process Data Out 6 | Fieldbus Process Data Out 6 | Read | ||
| AI | 24 | Process Data Out 7 | Fieldbus Process Data Out 7 | Read | ||
| AI | 25 | Process Data Out 8 | Fieldbus Process Data Out 8 | Read | ||
| MV | 0 | Control mode | Drive control mode: local (hand), remote or off | Read | 0=Local(Hand), 1=Remote, 2=OFF | |
| MVmin | 1 | Active fault code | Latest active fault code of the drive | Read | State text gives the active fault |
No points match these filters.
Object ID lookup: Johnson Controls Variable Speed Drive Series III point IDs by name
BV0Ready StateBV1Run/Stop StateBV2Fwd/Rev StateBV3Fault StateBV4Warning StateBV5At SetpointBV6At Zero SpeedBV7Motor Ctrl sourceBV8Speed Reference SourceBV9Run/Stop CMDBV10Fwd/Rev CMDBV11Reset FaultBV12Digital Input 1BV13Digital Input 2BV14Digital Input 3BV15Digital Input 4BV16Digital Input 5BV17Digital Input 6BV18Digital Input 7BV19Digital Input 8BV20Digital Output 1BV21Digital Output 2BV22Digital Output 3BV23Digital Output 4BV24Stop By CoastBV25Stop By RampBV26Belt BrokenBV27Drive Fan FailureBV28Force BypassBV29Fire ModeBV30DIN 1BV31DIN 2BV32DIN 3BV33DIN 4AV0Speed ReferenceAV1Current LimitAV2Min FrequencyAV3Maximum FrequencyAV4Accel Time 1AV5Decel Time 1AV6AnyParam IDAV7AnyParam ValueAV8Process Data In 1AV9Process Data In 2AV10Process Data In 3AV11Process Data In 4AV12Process Data In 5AV13Process Data In 6AV14Process Data In 7AV15Process Data In 8AI0Frequency SetpointAI1Output FrequencyAI2Motor SpeedAI3Motor LoadAI4Kilowatt Hours totalAI5Motor CurrentAI6DC link VoltageAI7Motor VoltageAI8Unit TemperatureAI9Motor TorqueAI10Operating DaysAI11Operating HoursAI12Motor TemperatureAI13Analog Input 1AI14Analog Input 2AI15Analog Output 1AI16Analog Output 2AI17Kilowatt InstantaneousAI18Process Data Out 1AI19Process Data Out 2AI20Process Data Out 3AI21Process Data Out 4AI22Process Data Out 5AI23Process Data Out 6AI24Process Data Out 7AI25Process Data Out 8MV0Control modeMV1Active fault code
Integration notes
- From the Variable Speed Drive Series III Communication Manual LIT-12013000 (September 2018): BACnet MS/TP Tables 58-61 (PDF pp55-57) and the BACnet IP section (PDF pp87-89), which print the same 78 objects.
- Enabling BACnet IP turns off BACnet MS/TP.
- AV 6/AV 7 AnyParam: write a parameter ID to AV 6 and read or write its value in AV 7.
- AV 8-15 and AI 18-25 are raw fieldbus process data; their content follows the P12.1/P12.2 process data selections.
- BV 21-23 (Digital Output 2-4) are described as relay outputs 1-3.
- C = commandable (priority array and relinquish default), per the manual.
Check it against the live device. A points list tells you what the controller can expose; the unit in front of you may differ by firmware or installed options. This list is provided as-is for reference only and may contain mistakes — confirming it before you write, map or commission anything is up to you (terms). Easy BACnet scans a network for BACnet IP devices from an Android phone, reads every object on the Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) and exports what it actually has to Excel — free. New to BACnet? Start with what a BACnet points list is and what the object types mean.
Questions about the Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP)
How many BACnet points does the Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) have?
This list has 78 BACnet objects: 26 analog inputs, 16 analog values, 34 binary values, 2 multi-state values. The exact set on a given unit depends on its firmware, installed options and configuration.
Which Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) BACnet points are writable?
29 of the 78 objects accept a write. Points marked Command have a priority array: a write holds until it is released, so release it back to automatic when you are done.
Where is the official Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) BACnet documentation?
The source is Variable Speed Drive Series III Communication Manual (BACnet MS/TP and BACnet/IP on-board communication) (LIT-12013000), revision 2018-09, published free by Johnson Controls at https://docs.johnsoncontrols.com/bas/api/khub/documents/XEo1PHGCK4nHiMO7HUpp~w/content.
What are the minimum BACnet points to integrate the Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP)?
Start with BV 9 Run/Stop CMD (Start/stop command (Run = start)); BV 7 Motor Ctrl source (Must be FBMotorCtrl for network run/stop); AV 0 Speed Reference (Speed reference, %); BV 8 Speed Reference Source (Must be FBSpeedRef for the network reference); BV 11 Reset Fault (Reset a tripped drive); BV 1 Run/Stop State (Running status); AI 1 Output Frequency (Output frequency, Hz); AI 5 Motor Current (Motor amps); BV 3 Fault State (Any active drive fault); MV 1 Active fault code (Active fault code).
How do I enable BMS control of the Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP)?
BV 7 Motor Ctrl source selects local or fieldbus (FBMotorCtrl) control of run/stop, and BV 8 Speed Reference Source selects local or fieldbus (FBSpeedRef) speed reference. MV 0 shows whether the drive is in Local (Hand), Remote or OFF.
Does the Johnson Controls Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP) need a BACnet heartbeat or have a communication timeout?
MS/TP: Comm Timeout BACnet (P12.3.3, default 10000 ms) raises a communication error if the drive is sole master for that long. BACnet IP: BACnet IP Comm Timeout (P12.4.3, 0 = no supervision) raises a fieldbus fault after that many seconds without messages; the parameter table prints default 0, while the text says the default is 10 s. A pulled Ethernet cable faults at once. The Modbus RTU/BACnet Fault Response and BACnet IP Fault Behavior parameters choose whether the fault is raised only in fieldbus control (0, default) or in all control places (1).
How do I check these points on the real Variable Speed Drive Series III (on-board BACnet MS/TP and BACnet IP)?
Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.
More Johnson Controls BACnet points lists
- Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2001 (Two-Pipe, On/Off Valve, Staged Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a multi-speed (staged) fan and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1100 with application #2001.
Also known as: ATC1100, LC-ATC1100-0, Application #2001, ATC app 2001, ATC1100 2001, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2002 (Two-Pipe, 0-10V Valve, Staged Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a multi-speed (staged) fan and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1100 with application #2002.
Also known as: ATC1100, LC-ATC1100-0, Application #2002, ATC app 2002, ATC1100 2002, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2003 (Two-Pipe, On/Off Valve, Staged Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a multi-speed (staged) fan and an optional on/off fresh-air damper, run by the Johnson Controls ATC1100 with application #2003.
Also known as: ATC1100, LC-ATC1100-0, Application #2003, ATC app 2003, ATC1100 2003, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2004 (Two-Pipe, 0-10V Valve, Staged Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a multi-speed (staged) fan and an optional on/off fresh-air damper, run by the Johnson Controls ATC1100 with application #2004.
Also known as: ATC1100, LC-ATC1100-0, Application #2004, ATC app 2004, ATC1100 2004, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2005 (Two-Pipe, On/Off Valve, Var-Speed Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a variable-speed fan and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1100 with application #2005.
Also known as: ATC1100, LC-ATC1100-0, Application #2005, ATC app 2005, ATC1100 2005, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2006 (Two-Pipe, 0-10V Valve, Var-Speed Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a variable-speed fan and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1100 with application #2006.
Also known as: ATC1100, LC-ATC1100-0, Application #2006, ATC app 2006, ATC1100 2006, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2007 (Two-Pipe, On/Off Valve, Var-Speed Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a variable-speed fan and an optional on/off fresh-air damper, run by the Johnson Controls ATC1100 with application #2007.
Also known as: ATC1100, LC-ATC1100-0, Application #2007, ATC app 2007, ATC1100 2007, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1100 Fan Coil Controller - Application #2008 (Two-Pipe, 0-10V Valve, Var-Speed Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a variable-speed fan and an optional on/off fresh-air damper, run by the Johnson Controls ATC1100 with application #2008.
Also known as: ATC1100, LC-ATC1100-0, Application #2008, ATC app 2008, ATC1100 2008, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3001 (Two-Pipe, On/Off Valve, Staged Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a multi-speed (staged) fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #3001.
Also known as: ATC1500, LC-ATC1500-0, Application #3001, ATC app 3001, ATC1500 3001, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3002 (Two-Pipe, On/Off Valve, Staged Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a multi-speed (staged) fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #3002.
Also known as: ATC1500, LC-ATC1500-0, Application #3002, ATC app 3002, ATC1500 3002, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3003 (Two-Pipe, 0-10V Valve, Staged Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a multi-speed (staged) fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #3003.
Also known as: ATC1500, LC-ATC1500-0, Application #3003, ATC app 3003, ATC1500 3003, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3004 (Two-Pipe, 0-10V Valve, Staged Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a multi-speed (staged) fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #3004.
Also known as: ATC1500, LC-ATC1500-0, Application #3004, ATC app 3004, ATC1500 3004, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3005 (Two-Pipe, On/Off Valve, Var-Speed Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a variable-speed fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #3005.
Also known as: ATC1500, LC-ATC1500-0, Application #3005, ATC app 3005, ATC1500 3005, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3006 (Two-Pipe, On/Off Valve, Var-Speed Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (on/off), a variable-speed fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #3006.
Also known as: ATC1500, LC-ATC1500-0, Application #3006, ATC app 3006, ATC1500 3006, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3007 (Two-Pipe, 0-10V Valve, Var-Speed Fan, Floating Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a variable-speed fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #3007.
Also known as: ATC1500, LC-ATC1500-0, Application #3007, ATC app 3007, ATC1500 3007, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #3008 (Two-Pipe, 0-10V Valve, Var-Speed Fan, On/Off Damper)
A two-pipe fan coil with one changeover heating/cooling valve (0-10 V proportional), a variable-speed fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #3008.
Also known as: ATC1500, LC-ATC1500-0, Application #3008, ATC app 3008, ATC1500 3008, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4001 (Four-Pipe, On/Off Valve, Staged Fan, Floating Damper)
A four-pipe fan coil with separate heating and cooling valves (on/off), a multi-speed (staged) fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #4001.
Also known as: ATC1500, LC-ATC1500-0, Application #4001, ATC app 4001, ATC1500 4001, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4002 (Four-Pipe, On/Off Valve, Staged Fan, On/Off Damper)
A four-pipe fan coil with separate heating and cooling valves (on/off), a multi-speed (staged) fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #4002.
Also known as: ATC1500, LC-ATC1500-0, Application #4002, ATC app 4002, ATC1500 4002, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4003 (Four-Pipe, 0-10V Valve, Staged Fan, Floating Damper)
A four-pipe fan coil with separate heating and cooling valves (0-10 V proportional), a multi-speed (staged) fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #4003.
Also known as: ATC1500, LC-ATC1500-0, Application #4003, ATC app 4003, ATC1500 4003, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4004 (Four-Pipe, 0-10V Valve, Staged Fan, On/Off Damper)
A four-pipe fan coil with separate heating and cooling valves (0-10 V proportional), a multi-speed (staged) fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #4004.
Also known as: ATC1500, LC-ATC1500-0, Application #4004, ATC app 4004, ATC1500 4004, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4005 (Four-Pipe, Six-Way Valve, Staged Fan, Floating Damper)
A four-pipe fan coil with a six-way valve for heating and cooling (0-10 V proportional), a multi-speed (staged) fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #4005.
Also known as: ATC1500, LC-ATC1500-0, Application #4005, ATC app 4005, ATC1500 4005, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4006 (Four-Pipe, Six-Way Valve, Staged Fan, On/Off Damper)
A four-pipe fan coil with a six-way valve for heating and cooling (0-10 V proportional), a multi-speed (staged) fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #4006.
Also known as: ATC1500, LC-ATC1500-0, Application #4006, ATC app 4006, ATC1500 4006, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4007 (Four-Pipe, On/Off Valve, Var-Speed Fan, Floating Damper)
A four-pipe fan coil with separate heating and cooling valves (on/off), a variable-speed fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #4007.
Also known as: ATC1500, LC-ATC1500-0, Application #4007, ATC app 4007, ATC1500 4007, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4008 (Four-Pipe, On/Off Valve, Var-Speed Fan, On/Off Damper)
A four-pipe fan coil with separate heating and cooling valves (on/off), a variable-speed fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #4008.
Also known as: ATC1500, LC-ATC1500-0, Application #4008, ATC app 4008, ATC1500 4008, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4009 (Four-Pipe, 0-10V Valve, Var-Speed Fan, Floating Damper)
A four-pipe fan coil with separate heating and cooling valves (0-10 V proportional), a variable-speed fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #4009.
Also known as: ATC1500, LC-ATC1500-0, Application #4009, ATC app 4009, ATC1500 4009, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4010 (Four-Pipe, 0-10V Valve, Var-Speed Fan, On/Off Damper)
A four-pipe fan coil with separate heating and cooling valves (0-10 V proportional), a variable-speed fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #4010.
Also known as: ATC1500, LC-ATC1500-0, Application #4010, ATC app 4010, ATC1500 4010, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4011 (Four-Pipe, Six-Way Valve, Var-Speed Fan, Floating Damper)
A four-pipe fan coil with a six-way valve for heating and cooling (0-10 V proportional), a variable-speed fan, two-wire PWM heating and an optional floating fresh-air damper with position output, run by the Johnson Controls ATC1500 with application #4011.
Also known as: ATC1500, LC-ATC1500-0, Application #4011, ATC app 4011, ATC1500 4011, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Fan coil unit controller
Johnson Controls ATC1500 Fan Coil Controller - Application #4012 (Four-Pipe, Six-Way Valve, Var-Speed Fan, On/Off Damper)
A four-pipe fan coil with a six-way valve for heating and cooling (0-10 V proportional), a variable-speed fan, two-wire PWM heating and an optional on/off fresh-air damper, run by the Johnson Controls ATC1500 with application #4012.
Also known as: ATC1500, LC-ATC1500-0, Application #4012, ATC app 4012, ATC1500 4012, Advanced Terminal Unit Controller, ATC SMART Equipment Controller - Power and energy meter (multi-circuit, BACnet MS/TP or BACnet IP)
Johnson Controls EEM Multi-Circuit Electric Energy Meter - Load Device
Each configured load (virtual BACnet device) of the Johnson Controls EEM multi-circuit electric energy meter.
Also known as: EEM Multi-Circuit load, EEM-MULTI-03, EEM-MULTI-12, EEM-MULTI-48, Electric Energy Meter Multi-Circuit, JCI EEM - Power and energy meter (multi-circuit, BACnet MS/TP or BACnet IP)
Johnson Controls EEM Multi-Circuit Electric Energy Meter - Root Device
The root (panel) device of the Johnson Controls EEM multi-circuit electric energy meter in its 3, 12 and 48-load versions.
Also known as: EEM Multi-Circuit, EEM-MULTI-03, EEM-MULTI-12, EEM-MULTI-48, Electric Energy Meter Multi-Circuit, JCI EEM - Power and energy meter (3-phase, BACnet MS/TP)
Johnson Controls EM Series 3-Phase Energy Meter with EMCOMMS Module (BACnet MS/TP)
The Johnson Controls EM series three-phase energy meter: the EMCOMMS communication module with its CVT voltage/current sensors, one per phase.
Also known as: EMCOMMS, EM Series, EM 3 Phase Energy Meter, JCI EM meter, EMCOMMS BACnet - Evaporative condenser controller
Johnson Controls Frick XLP3b Evaporative Condenser Controller (BMS points)
Johnson Controls / Frick XLP3b evaporative condensers for industrial refrigeration with the factory PLC control panel (up to eight fans and a pump).
Also known as: XLP3b, Frick XLP3b, XLP3b evaporative condenser, 140.925-IOM - Laboratory VAV controller (fume hood)
Johnson Controls HMS-2000 Fume Hood Controller (BACnet MS/TP)
Fume hoods controlled and monitored by the Johnson Controls HMS-2000 touchscreen fume hood controller with face velocity, sash, pressure and airflow inputs.
Also known as: HMS-2000, HMS2000, LB-HMS2C, Hood Monitoring Station, JCI fume hood controller - Laboratory VAV controller (fume hood)
Johnson Controls HMS1655 Fume Hood Controller (BACnet MS/TP)
Fume hoods controlled and monitored by the Johnson Controls HMS1655 fume hood controller with face velocity, sash, pressure, airflow and temperature inputs.
Also known as: HMS1655, HMS-1655, Hood Monitoring Station, JCI fume hood controller - Water-to-water heat pump
Johnson Controls JMWL-Series 30-70 Ton Modular Water-to-Water Heat Pump
Johnson Controls JMWL-Series 30-70 ton modular water-to-water heat pump modules with the factory master controller.
Also known as: JMWL, JMWL-Series, JMWL360, JMWL600, JMWL840, JMW600, 14807-NOM1, 97B0090N02, JCI modular water-to-water heat pump - Water-source heat pump controller
Johnson Controls PEAK 18 SMART Equipment Controller - Water-Source Heat Pump (PK-OEM1820)
Water-source heat pumps with a factory PEAK OEM 18 (24 V) SMART Equipment controller linked over Modbus to one or two Aurora (ABC) unit boards.
Also known as: PEAK 18, PK-OEM1820-0, PK-OEM18x0-0, PEAK OEM 18, SMART Equipment controller, 147.00-EG1, Aurora ABC - Rooftop unit controller
Johnson Controls Premier Rooftop Units 25-50 Ton
Johnson Controls Premier 25-50 ton R-410A packaged rooftop units (MZVAV or SZVAV) with the Applied Smart Equipment controller.
Also known as: JCI Premier RTU, Premier 25-50 ton, Applied Smart Equipment controller, Smart Equipment rooftop, 5586996-JSG-A - Rooftop unit BACnet gateway
Johnson Controls Simplicity LINC Gateway (YORK / JCI Unitary Products rooftops)
Johnson Controls Unitary Products (YORK, Coleman, Luxaire) packaged rooftop units with Simplicity controls built after 4/2/2008, plus older Simplicity Elite and Simplicity with Intelli-Comfort controls, fitted with the Simplicity LINC gateway.
Also known as: Simplicity LINC, Simplicity-LINC, SimplicityLINC, YORK Simplicity LINC, 1031990-UAD-A-0313, YORK_RTU, Simplicity Elite, Intelli-Comfort, Sun-Line, Predator, YORK Simplicity BACnet - Fan coil unit controller (room thermostat)
Johnson Controls T8800 Series Touch Screen Fan Coil Thermostat (BACnet MS/TP)
Two- and four-pipe fan coils with three-speed fans and on/off or modulating valves, using the T8800 touch screen thermostat (TF20, TB20, TB21).
Also known as: T8800, T8800-TF20, T8800-TB20, T8800-TB21 - Fan coil unit controller (room thermostat)
Johnson Controls T9800 Series Touch Screen Fan Coil Thermostat (BACnet MS/TP)
Two- and four-pipe fan coils (relay or 0-10 VDC valves, three-speed or ECM fans), fan coils with floor heating or TiO2/ESP, water source heat pumps, boilers and a basic AHU application, using the T9800 touch screen thermostat.
Also known as: T9800, T9800-TF20-9JS0, T9800-TF21-9JS0, T9800-TB21-9JS0, T9800-TF20-1JS0, T9800-TF21-1JS0, T9800-TB21-1JS0 - Rooftop unit controller (room thermostat)
Johnson Controls TEC2601-4 and TEC2601-4+PIR Single-Stage Thermostat (BACnet MS/TP)
Single-stage heating and cooling equipment such as small rooftop units and split systems with 24 VAC G/Y1/W1 control, using the TEC2601-4 thermostat.
Also known as: TEC2601-4, TEC2601-4+PIR, TEC2601 - Rooftop unit controller (room thermostat for heat-pump units)
Johnson Controls TEC2602-4 and TEC2602-4+PIR Heat Pump Thermostat (BACnet MS/TP)
Single- or two-stage heat pumps with auxiliary heat and a reversing valve, using the TEC2602-4 thermostat.
Also known as: TEC2602-4, TEC2602-4+PIR, TEC2602 - Rooftop unit controller (room thermostat)
Johnson Controls TEC2603-4 and TEC2603-4+PIR Multi-Stage Thermostat (BACnet MS/TP)
Rooftop units and split systems with up to two heating and two cooling stages, using the TEC2603-4 thermostat.
Also known as: TEC2603-4, TEC2603-4+PIR, TEC2603 - Rooftop unit controller (room thermostat with economizer)
Johnson Controls TEC2604-4 and TEC2604-4+PIR Multi-Stage Economizer Thermostat (BACnet MS/TP)
Rooftop units with an economizer and up to two heating and two cooling stages, using the TEC2604-4 thermostat.
Also known as: TEC2604-4, TEC2604-4+PIR, TEC2604 - Rooftop unit controller (room thermostat with humidity control)
Johnson Controls TEC2613-4 and TEC2613-4+PIR Multi-Stage Temperature and Humidity Controller (BACnet MS/TP)
Multi-stage rooftop units and split systems that also dehumidify or drive a humidifier, using the TEC2613-4 controller.
Also known as: TEC2613-4, TEC2613-4+PIR, TEC2613 - Fan coil unit controller (room thermostat)
Johnson Controls TEC2645-2 Thermostat with Single Proportional Output and One-Speed Fan (BACnet MS/TP)
Johnson Controls TEC2645-2 BACnet MS/TP networked thermostats with one 0-10 VDC proportional output and one-speed fan control (the -2 generation; the newer TEC2645-4 is a separate entry with different instances).
Also known as: TEC2645-2, TEC2645, TEC2645-2 networked thermostat - Fan coil unit controller (room thermostat)
Johnson Controls TEC2645-4 Thermostat with Single Proportional Output and One-Speed Fan (BACnet MS/TP)
Fan coils, reheat valves and zoning equipment with one 0-10 VDC proportional output and a single-speed fan, using the TEC2645-4 thermostat.
Also known as: TEC2645-4, TEC2645 - VAV zone controller (room thermostat for TEC zoning)
Johnson Controls TEC2647Z-3 / TEC2647Z-3+PIR Zone Controller (TEC Zoning System, BACnet MS/TP)
Zone dampers in the Johnson Controls TEC zoning system, each run by a TEC2647Z-3 zone controller (optionally with PIR occupancy sensor) and served by a TEC2664Z-3 rooftop controller.
Also known as: TEC2647Z-3, TEC2647Z-3+PIR, TEC2647Z, TEC2647Z-2, TEC zoning zone controller - Rooftop unit controller (TEC zoning system)
Johnson Controls TEC2664Z-3 Rooftop Controller (TEC Zoning System, BACnet MS/TP)
Constant volume, pressure-dependent rooftop units with up to two heating and two cooling stages and a bypass damper, run by the TEC2664Z-3 rooftop controller of the Johnson Controls TEC zoning system.
Also known as: TEC2664Z-3, TEC2664Z, TEC2664Z-2, TEC zoning rooftop controller - Fan coil unit controller (room thermostat)
Johnson Controls TEC26x6(H)-2 Series Fan Coil Thermostat with Dehumidification and Three Fan Speeds (BACnet MS/TP)
Two- or four-pipe fan coils and cabinet unit heaters with three fan speeds, using the older TEC26x6(H)-2 thermostats.
Also known as: TEC2616-2, TEC2626-2, TEC2636-2, TEC2646-2, TEC2656-2, TEC2636H-2, TEC2656H-2, TEC26x6-2 - Fan coil unit controller (room thermostat)
Johnson Controls TEC26x6(H)-4 and TEC26x6H-4+PIR Fan Coil Thermostat (BACnet MS/TP)
Two- or four-pipe fan coils with up to three fan speeds, controlled by the TEC26x6(H)-4 family (on/off, floating or proportional valve outputs, optional dehumidification and PIR occupancy sensing).
Also known as: TEC2616-4, TEC2626-4, TEC2636-4, TEC2646-4, TEC2656-4, TEC2616H-4, TEC2636H-4+PIR, TEC2656H-4+PIR, TEC26x6-4 - VAV zone controller (room thermostat)
Johnson Controls TEC26x7-2 Series Thermostat with Two Outputs (BACnet MS/TP)
Hydronic reheat valves, pressure-dependent VAV boxes with or without reheat and other zoning equipment, using the older TEC26x7-2 two-output thermostats.
Also known as: TEC2627-2, TEC2647-2, TEC26x7-2 - VAV zone controller (room thermostat)
Johnson Controls TEC26x7-4 and TEC26x7-4+PIR Thermostat with Two Outputs (BACnet MS/TP)
Hydronic reheat valves, pressure-dependent VAV boxes with or without reheat and other zoning equipment, using the two-output TEC26x7-4 thermostats (TEC2627 on/off or floating, TEC2647 proportional).
Also known as: TEC2627-4, TEC2647-4, TEC2627-4+PIR, TEC2647-4+PIR, TEC26x7-4 - VAV zone controller (room thermostat for VVT zoning)
Johnson Controls TEC26x7VVT-2 Series Thermostat with Two Outputs for VVT Systems (BACnet MS/TP)
Pressure-dependent VAV and VVT zone dampers with or without local reheat, using the TEC26x7VVT-2 thermostats with floating or 0-10 VDC outputs.
Also known as: TEC2627VVT-2, TEC2647VVT-2, TEC26x7VVT-2, TEC26x7VVT - Fan coil unit controller (room thermostat)
Johnson Controls TEC26xx-0+PIR Thermostat Controller (BACnet MS/TP)
Fan coils and zoning equipment controlled by the TEC26xx-0+PIR thermostats, which add remote input and heat/cool output configuration objects to the TEC26x6 object set.
Also known as: TEC26xx-0+PIR, TEC26xx-0 - Fan coil unit controller (room thermostat)
Johnson Controls TEC3000 Series TEC3610 / TEC3611 / TEC3612 / TEC3613 On/Off or Floating Fan Coil Thermostat (BACnet MS/TP)
Two- or four-pipe fan coils, cabinet unit heaters, reheat valves and pressure-dependent VAV zones with on/off or floating outputs, using the networked TEC3610-TEC3613 thermostats.
Also known as: TEC3610, TEC3611, TEC3612, TEC3613, TEC361x, TEC3000 on/off floating, JCI TEC3000 fan coil - Fan coil unit controller (room thermostat)
Johnson Controls TEC3000 Series TEC3620 / TEC3621 / TEC3622 / TEC3623 Proportional Fan Coil Thermostat (BACnet MS/TP)
Two- or four-pipe fan coils, cabinet unit heaters, reheat valves and pressure-dependent VAV zones with 0-10 VDC proportional outputs, using the networked TEC3620-TEC3623 thermostats.
Also known as: TEC3620, TEC3621, TEC3622, TEC3623, TEC362x, TEC3000 proportional, JCI TEC3000 0-10V fan coil - Rooftop unit controller (room thermostat, conventional or heat-pump RTUs)
Johnson Controls TEC3000 Series TEC3630 / TEC3631 Single- or Two-Stage RTU / Heat Pump Thermostat with Economizer (BACnet MS/TP)
Single- or two-stage unitary rooftop units and heat-pump RTUs, with or without an economizer, using the networked TEC3630 and TEC3631 thermostats.
Also known as: TEC3630, TEC3631, TEC363x, TEC3000 economizer, JCI TEC3000 rooftop thermostat - VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-1 (Cooling only)
A single-duct cooling-only VAV box controlled by the Johnson Controls VAV1717 with preloaded application 1717-1.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-1, VAV1717 Cooling only - Fan-powered VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-10 (Elec Reheat 1 Stg On/Off Series Fan)
A series fan-powered VAV box with a single-speed fan and one stage of electric reheat controlled by the Johnson Controls VAV1717 with preloaded application 1717-10.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-10, VAV1717 Elec Reheat 1 Stg On/Off Series Fan - VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-2 (Elec Reheat 1-2 Stg)
A single-duct VAV box with one or two stages of electric reheat controlled by the Johnson Controls VAV1717 with preloaded application 1717-2.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-2, VAV1717 Elec Reheat 1-2 Stg - VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-3 (On/Off HW Reheat)
A single-duct VAV box with an on/off hot water reheat valve controlled by the Johnson Controls VAV1717 with preloaded application 1717-3.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-3, VAV1717 On/Off HW Reheat - VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-4 (Incr HW Reheat)
A single-duct VAV box with an incremental (floating) hot water reheat valve controlled by the Johnson Controls VAV1717 with preloaded application 1717-4.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-4, VAV1717 Incr HW Reheat - Fan-powered VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-5 (On/Off Parallel Fan)
A parallel fan-powered VAV box with a single-speed fan controlled by the Johnson Controls VAV1717 with preloaded application 1717-5.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-5, VAV1717 On/Off Parallel Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-6 (On/Off HW Reheat On/Off Parallel Fan)
A parallel fan-powered VAV box with a single-speed fan and an on/off hot water reheat valve controlled by the Johnson Controls VAV1717 with preloaded application 1717-6.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-6, VAV1717 On/Off HW Reheat On/Off Parallel Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-7 (Elec Reheat 1 Stg On/Off Parallel Fan)
A parallel fan-powered VAV box with a single-speed fan and one stage of electric reheat controlled by the Johnson Controls VAV1717 with preloaded application 1717-7.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-7, VAV1717 Elec Reheat 1 Stg On/Off Parallel Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-8 (On/Off Series Fan)
A series fan-powered VAV box with a single-speed fan controlled by the Johnson Controls VAV1717 with preloaded application 1717-8.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-8, VAV1717 On/Off Series Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1717 VAV Controller - Application 1717-9 (On/Off HW Reheat On/Off Series Fan)
A series fan-powered VAV box with a single-speed fan and an on/off hot water reheat valve controlled by the Johnson Controls VAV1717 with preloaded application 1717-9.
Also known as: VAV1717, JC-VAV1717-0, Application 1717-9, VAV1717 On/Off HW Reheat On/Off Series Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-1 (Elec Reheat 1-3 Stg On/Off Parallel Fan)
A parallel fan-powered VAV box with a single-speed fan and one to three stages of electric reheat controlled by the Johnson Controls VAV1732 with preloaded application 1732-1.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-1, VAV1732 Elec Reheat 1-3 Stg On/Off Parallel Fan - VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-10 (Proportional HW Reheat)
A single-duct VAV box with a proportional (0-10 VDC) hot water reheat valve controlled by the Johnson Controls VAV1732 with preloaded application 1732-10.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-10, VAV1732 Proportional HW Reheat - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-2 (Incr HW Reheat On/Off Parallel Fan)
A parallel fan-powered VAV box with a single-speed fan and an incremental hot water reheat valve controlled by the Johnson Controls VAV1732 with preloaded application 1732-2.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-2, VAV1732 Incr HW Reheat On/Off Parallel Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-3 (Elec Reheat 1-3 Stg On/Off Series Fan)
A series fan-powered VAV box with a single-speed fan and one to three stages of electric reheat controlled by the Johnson Controls VAV1732 with preloaded application 1732-3.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-3, VAV1732 Elec Reheat 1-3 Stg On/Off Series Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-4 (Incr HW Reheat On/Off Series Fan)
A series fan-powered VAV box with a single-speed fan and an incremental hot water reheat valve controlled by the Johnson Controls VAV1732 with preloaded application 1732-4.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-4, VAV1732 Incr HW Reheat On/Off Series Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-5 (Var Speed Series Fan)
A series fan-powered VAV box with a variable-speed fan controlled by the Johnson Controls VAV1732 with preloaded application 1732-5.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-5, VAV1732 Var Speed Series Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-6 (Elec Reheat 1-3 Stg Var Speed Series Fan)
A series fan-powered VAV box with a variable-speed fan and one to three stages of electric reheat controlled by the Johnson Controls VAV1732 with preloaded application 1732-6.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-6, VAV1732 Elec Reheat 1-3 Stg Var Speed Series Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-7 (On/Off HW Reheat Var Speed Series Fan)
A series fan-powered VAV box with a variable-speed fan and an on/off hot water reheat valve controlled by the Johnson Controls VAV1732 with preloaded application 1732-7.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-7, VAV1732 On/Off HW Reheat Var Speed Series Fan - Fan-powered VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-8 (Incr HW Reheat Var Speed Series Fan)
A series fan-powered VAV box with a variable-speed fan and an incremental hot water reheat valve controlled by the Johnson Controls VAV1732 with preloaded application 1732-8.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-8, VAV1732 Incr HW Reheat Var Speed Series Fan - VAV terminal unit controller
Johnson Controls VAV1732 VAV Controller - Application 1732-9 (Elec Reheat 1-3 Stg)
A single-duct VAV box with one to three stages of electric reheat controlled by the Johnson Controls VAV1732 with preloaded application 1732-9.
Also known as: VAV1732, JC-VAV1732-0, Application 1732-9, VAV1732 Elec Reheat 1-3 Stg - Variable frequency drive (HVAC)
Johnson Controls VSD Series II HVAC drive (BACnet MS/TP and BACnet IP)
Johnson Controls VSD Series II HVAC drives using the built-in RS-485 port (BACnet MS/TP) or the Ethernet port (BACnet IP).
Also known as: VSD Series II, Variable Speed Drive Series II, JCI VSD2, VSD Series 2, LIT-12011771
Source: Variable Speed Drive Series III Communication Manual (BACnet MS/TP and BACnet/IP on-board communication) · LIT-12013000 · rev. 2018-09. Object names, instances and units are reproduced as published; descriptions are our own.