Easy BACnetEvaporative humidifier · BACnet points list
Neptronic SKV BACnet points list
Updated 28 October 2026
Short answer
The SKV is a multi-module evaporative humidifier. Its controller speaks BACnet MS/TP and exposes control mode and source selection, network setpoints and readings, a network fallback timeout, and per-module (1-4) demand, state, valve, float and fault objects.
This page lists 277 BACnet objects for the Neptronic SKV — 242 of them writable — with each object’s type, instance number, name, engineering units and access. It is re-typed from Neptronic’s own free documentation, linked below.
- Manufacturer
- Neptronic
- Model
- SKV
- Equipment
- Evaporative humidifier
- Equipment type
- Humidifiers
- BACnet objects
- 277 (242 writable)
- Transport
- BACnet MS/TP
- Firmware
- Not stated
- Default device instance
- 153000 by default
- Also known as
- SKV evaporative humidifier, SKV BACnet
Download CSV 277 rows
Download EDE B.I.G.-EU
JSON
Manufacturer PDF ↗
Download Easy BACnet Mobile App Google Play
BMS integration notes: Neptronic SKV
Integration in brief
Set MSV 4 ControlMode to Network (or an internal mode with network sources) and write demand to AV 5, or feed room RH via MSV 3 = Network. Turn the system on with BV 116 SystemPower and keep network values fresh inside the fallback timeout (AV 38).
Minimum points to map
The short list most integrators start with — enough to run the unit from a BMS. Map more as the job needs.
| Object | Name | Why | Access |
|---|---|---|---|
| BV 116 | SystemPower | System power on/off | Write |
| MV 4 | ControlMode | Control mode (6 = Network) | Write |
| AV 5 | SystDemand | Demand from the BMS, % (when MSV 4 = Network) | Write |
| AV 16 | SetpointRH | BMS RH setpoint (when MSV 5 = Network) | Write |
| AV 13 | RoomRH | BMS room RH (when MSV 3 = Network) | Write |
| MV 16 | Module1State | Stand-by/drain/fill/ready/alarm state of module 1 | Write |
| AV 1 | SystOutput | Actual system output % | Write |
| BV 118 | AlarmRelay | Closed on any alarm but airflow cutout/service warning | Write |
| BV 121 | NetworkFallbackAlarm | On when network values time out (AV 38) | Write |
Enable & remote start
BV 116 SystemPower: ON = normal operation, OFF = demand inhibited. MSV 4 ControlMode selects an analog input, internal temperature/RH control or Network.
Heartbeat & communication loss
AV 38 NetworkFallbackTimeout (1-15 min) applies whenever at least one control input uses Network as its source; AV 39 counts down and BV 121 NetworkFallbackAlarm turns on when it expires.
Sensors & values from the BMS
Set MSV 3 RoomRHSource or MSV 2 RoomTempSource to Network and write the values from the BMS; MSV 5 SetpointSource = Network uses the external setpoints AV 16 (RH) and AV 17 (temperature).
Network setup
- MS/TP MAC defaults to 000 (000-254; 128-254 are non-token-passing slaves); baud auto-detects (Auto, 9600, 19200, 38400, 76800); Max_Master 127.
- Device instance defaults to 153000 and can be set from the menu or via Device Object_Identifier.
Watch out for
- Older (2018) guide: the W? column marks every object as Present Value, so confirm writability on site.
- Faults that stop a module need a manual reset (BV 95 SystResetAlarms or the Diagnostic menu).
- BV 107 RunWhileServiceAlarm decides whether modules keep running when a service alarm is due.
Neptronic SKV BACnet objects
Type: AI, AO, AV, BI, BO, BV, MI/MO/MV (multi-state) · Access: Read read-only, Write writable, Command writable with a priority array.
Note: the source document has no read/write column, so access here is inferred from the object type (inputs read-only, values writable). Confirm on the live controller before writing.
| Description | States | |||||
|---|---|---|---|---|---|---|
| AI | 1 | ExternalDemand | External demand signal measurement | mV | Read | |
| AI | 2 | ExternalSetpoint | External setpoint signal measurement | mV | Read | |
| AI | 3 | RoomTempSensor | Room temperature sensor signal measurement | mV | Read | |
| AI | 4 | RoomRHSensor | Room relative humidity sensor signal measurement | mV | Read | |
| AI | 5 | DuctSensor | Duct relative humidity sensor signal measurement | mV | Read | |
| AI | 6 | Module1WaterLevelSensor | Module 1 water level sensor signal measurement | Hz | Read | |
| AI | 7 | Module2WaterLevelSensor | Module 2 water level sensor signal measurement | Hz | Read | |
| AI | 8 | Module3WaterLevelSensor | Module 3 water level sensor signal measurement | Hz | Read | |
| AI | 9 | Module4WaterLevelSensor | Module 4 water level sensor signal measurement | Hz | Read | |
| AI | 10 | Module1WaterTempSensor | Module 1 water temperature sensor signal measurement | mV | Read | |
| AI | 11 | Module2WaterTempSensor | Module 2 water temperature sensor signal measurement | mV | Read | |
| AI | 12 | Module3WaterTempSensor | Module 3 water temperature sensor signal measurement | mV | Read | |
| AI | 13 | Module4WaterTempSensor | Module 4 water temperature sensor signal measurement | mV | Read | |
| AVmin | 1 | SystOutput | System output in percent | % | Write | |
| AV | 2 | SystOutput | System output in Mass Flow units | Write | ||
| AV | 3 | SystCapacity | Total system output capacity | Write | ||
| AV | 4 | NumOfModules | Number of humidifier modules | Write | ||
| AVmin | 5 | SystDemand | System demand | % | Write | |
| AV | 6 | SystLimit | System output limit as per high limit signals | % | Write | |
| AV | 7 | SystOutputLockOn | System output lock or limit for load shedding | % | Write | |
| AV | 8 | SystFeedback | System output feedback signal | mV | Write | |
| AV | 9 | SimDemand | Simulation mode demand | % | Write | |
| AV | 10 | SimDuration | Simulation mode duration | min | Write | |
| AV | 11 | SimCountdown | Simulation mode countdown | s | Write | |
| AV | 12 | AnalogDemand | Analog system demand | % | Write | |
| AVmin | 13 | RoomRH | Room relative humidity | %RH | Write | |
| AV | 14 | RoomTemp | Room temperature | Write | ||
| AV | 15 | DuctRH | Duct relative humidity | %RH | Write | |
| AVmin | 16 | SetpointRH | External relative humidity setpoint | %RH | Write | |
| AV | 17 | SetpointTemp | External temperature setpoint | Write | ||
| AV | 18 | InternalSetpointOccupied | Internal %RH setpoint during occupancy | % | Write | |
| AV | 19 | InternalSetpointOccupied | Internal temperature setpoint during occupancy | °F or °C | Write | |
| AV | 20 | InternalSetpointUnoccupied | Internal %RH setpoint during occupancy | % | Write | |
| AV | 21 | InternalSetpointUnoccupied | Internal temperature setpoint during occupancy | °F or °C | Write | |
| AV | 22 | InternalSetpointVacant | Internal %RH setpoint during vacancy | % | Write | |
| AV | 23 | InternalSetpointVacant | Internal temperature setpoint during vacancy | °F or °C | Write | |
| AV | 24 | ProportionalRamp | Proportional ramp for %RH | %RH | Write | |
| AV | 25 | ProportionalRamp | Proportional ramp for temperature | °F or °C | Write | |
| AV | 26 | IntegralRamp | Integral ramp for %RH | %RH | Write | |
| AV | 27 | IntegralRamp | Integral ramp for temperature | °F or °C | Write | |
| AV | 28 | Deadband | Deadband for %RH | %RH | Write | |
| AV | 29 | Deadband | Deadband for temperature | °F or °C | Write | |
| AV | 30 | HighLimitSetpoint | Analog high limit setpoint value | %RH | Write | |
| AV | 31 | HighLimitProportionalRamp | Analog high limit proportional ramp | %RH | Write | |
| AV | 32 | DilutionInterval | Water dilution interval | min | Write | |
| AV | 33 | DilutionCycles | Number of water dilution cycles | Write | ||
| AV | 34 | CleaningInterval | Cleaning interval | months | Write | |
| AV | 35 | AutoDrainInterval | Automatic drain interval | h | Write | |
| AV | 36 | UVLampInterval | UV lamp replacement interval | h | Write | |
| AV | 37 | InactivityDelay | System inactivity delay | h | Write | |
| AV | 38 | NetworkFallbackTimeout | Network fallback timeout | min | Write | |
| AV | 39 | NetworkTimeoutCountdown | Network fallback timeout countdown | s | Write | |
| AV | 40 | InactivityCounter | System inactivity downcounter | s | Write | |
| AV | 41 | Module1DrainTimeoutCountdown | Module 1 drain timeout countdown | s | Write | |
| AV | 42 | Module2DrainTimeoutCountdown | Module 2 drain timeout countdown | s | Write | |
| AV | 43 | Module3DrainTimeoutCountdown | Module 3 drain timeout countdown | s | Write | |
| AV | 44 | Module4DrainTimeoutCountdown | Module 4 drain timeout countdown | s | Write | |
| AV | 45 | Module1FillTimeoutCountdown | Module 1 fill timeout countdown | s | Write | |
| AV | 46 | Module2FillTimeoutCountdown | Module 2 fill timeout countdown | s | Write | |
| AV | 47 | Module3FillTimeoutCountdown | Module 3 fill timeout countdown | s | Write | |
| AV | 48 | Module4FillTimeoutCountdown | Module 4 fill timeout countdown | s | Write | |
| AV | 49 | Module1InactivityCountdown | Module 1 inactivity countdown | s | Write | |
| AV | 50 | Module2InactivityCountdown | Module 2 inactivity countdown | s | Write | |
| AV | 51 | Module3InactivityCountdown | Module 3 inactivity countdown | s | Write | |
| AV | 52 | Module4InactivityCountdown | Module 4 inactivity countdown | s | Write | |
| AV | 53 | Module1StateCountdown | Module 1 state countdown | Write | ||
| AV | 54 | Module2StateCountdown | Module 2 state countdown | Write | ||
| AV | 55 | Module3StateCountdown | Module 3 state countdown | Write | ||
| AV | 56 | Module4StateCountdown | Module 4 state countdown | Write | ||
| AV | 57 | Module1Demand | Module 1 demand | % | Write | |
| AV | 58 | Module2Demand | Module 2 demand | % | Write | |
| AV | 59 | Module3Demand | Module 3 demand | % | Write | |
| AV | 60 | Module4Demand | Module 4 demand | % | Write | |
| AV | 61 | Module1Output | Module 1 output | % | Write | |
| AV | 62 | Module2Output | Module 2 output | % | Write | |
| AV | 63 | Module3Output | Module 3 output | % | Write | |
| AV | 64 | Module4Output | Module 4 output | % | Write | |
| AV | 65 | Module1Capacity | Module 1 total capacity | Write | ||
| AV | 66 | Module2Capacity | Module 2 total capacity | Write | ||
| AV | 67 | Module3Capacity | Module 3 total capacity | Write | ||
| AV | 68 | Module4Capacity | Module 4 total capacity | Write | ||
| AV | 69 | Module1WaterLevel | Module 1 water level | % | Write | |
| AV | 70 | Module2WaterLevel | Module 2 water level | % | Write | |
| AV | 71 | Module3WaterLevel | Module 3 water level | % | Write | |
| AV | 72 | Module4WaterLevel | Module 4 water level | % | Write | |
| AV | 73 | Module1WaterTemp | Module 1 water temperature | °F or °C | Write | |
| AV | 74 | Module2WaterTemp | Module 2 water temperature | °F or °C | Write | |
| AV | 75 | Module3WaterTemp | Module 3 water temperature | °F or °C | Write | |
| AV | 76 | Module4WaterTemp | Module 4 water temperature | °F or °C | Write | |
| AV | 77 | Module1PumpStageWeight | Module 1 pump's stage weight relative to module's full capacity | % | Write | |
| AV | 78 | Module2PumpStageWeight | Module 2 pump's stage weight relative to module's full capacity | % | Write | |
| AV | 79 | Module3PumpStageWeight | Module 3 pump's stage weight relative to module's full capacity | % | Write | |
| AV | 80 | Module4PumpStageWeight | Module 4 pump's stage weight relative to module's full capacity | % | Write | |
| AV | 81 | Module1Valve1StageWeight | Stage weight of Module 1, valve 1 relative to module's full capacity | % | Write | |
| AV | 82 | Module2Valve1StageWeight | Stage weight of Module 2, valve 1 relative to module's full capacity | % | Write | |
| AV | 83 | Module3Valve1StageWeight | Stage weight of Module 3, valve 1 relative to module's full capacity | % | Write | |
| AV | 84 | Module4Valve1StageWeight | Stage weight of Module 4, valve 1 relative to module's full capacity | % | Write | |
| AV | 85 | Module1Valve2StageWeight | Stage weight of Module 1, valve 2 relative to module's full capacity | % | Write | |
| AV | 86 | Module2Valve2StageWeight | Stage weight of Module 2, valve 2 relative to module's full capacity | % | Write | |
| AV | 87 | Module3Valve2StageWeight | Stage weight of Module 3, valve 2 relative to module's full capacity | % | Write | |
| AV | 88 | Module4Valve2StageWeight | Stage weight of Module 4, valve 2 relative to module's full capacity | % | Write | |
| AV | 89 | Module1Valve3StageWeight | Stage weight of Module 1, valve 3 relative to module's full capacity | % | Write | |
| AV | 90 | Module2Valve3StageWeight | Stage weight of Module 2, valve 3 relative to module's full capacity | % | Write | |
| AV | 91 | Module3Valve3StageWeight | Stage weight of Module 3, valve 3 relative to module's full capacity | % | Write | |
| AV | 92 | Module4Valve3StageWeight | Stage weight of Module 4, valve 3 relative to module's full capacity | % | Write | |
| AV | 93 | Module1Valve4StageWeight | Stage weight of Module 1, valve 4 relative to module's full capacity | % | Write | |
| AV | 94 | Module2Valve4StageWeight | Stage weight of Module 2, valve 4 relative to module's full capacity | % | Write | |
| AV | 95 | Module3Valve4StageWeight | Stage weight of Module 3, valve 4 relative to module's full capacity | % | Write | |
| AV | 96 | Module4Valve4StageWeight | Stage weight of Module 4, valve 4 relative to module's full capacity | % | Write | |
| AV | 97 | Module1TotalDuty | Total duty of Module 1 (in hours) at 100% output | h | Write | |
| AV | 98 | Module2TotalDuty | Total duty of Module 2 (in hours) at 100% output | h | Write | |
| AV | 99 | Module3TotalDuty | Total duty of Module 3 (in hours) at 100% output | h | Write | |
| AV | 100 | Module4TotalDuty | Total duty of Module 4 (in hours) at 100% output | h | Write | |
| BV | 1 | Module1DrainRequest | Drain request for Module 1 | Write | 0=OFF, 1=ON | |
| BV | 2 | Module2DrainRequest | Drain request for Module 2 | Write | 0=OFF, 1=ON | |
| BV | 3 | Module3DrainRequest | Drain request for Module 3 | Write | 0=OFF, 1=ON | |
| BV | 4 | Module4DrainRequest | Drain request for Module 4 | Write | 0=OFF, 1=ON | |
| BV | 5 | Module1Inactivity | Inactivity state for Module 1 | Write | 0=True, 1=False | |
| BV | 6 | Module2Inactivity | Inactivity state for Module 2 | Write | 0=True, 1=False | |
| BV | 7 | Module3Inactivity | Inactivity state for Module 3 | Write | 0=True, 1=False | |
| BV | 8 | Module4Inactivity | Inactivity state for Module 4 | Write | 0=True, 1=False | |
| BV | 9 | Module1SilverIonChangeDue | Date on which Silver Ion cartridge change is due for Module 1 | Write | 0=True, 1=False | |
| BV | 10 | Module2SilverIonChangeDue | Date on which Silver Ion cartridge change is due for Module 2 | Write | 0=True, 1=False | |
| BV | 11 | Module3SilverIonChangeDue | Date on which Silver Ion cartridge change is due for Module 3 | Write | 0=True, 1=False | |
| BV | 12 | Module4SilverIonChangeDue | Date on which Silver Ion cartridge change is due for Module 4 | Write | 0=True, 1=False | |
| BV | 13 | Module1UVLampChangeDue | Date on which UV lamp change is due for Module 1 | Write | 0=True, 1=False | |
| BV | 14 | Module2UVLampChangeDue | Date on which UV lamp change is due for Module 2 | Write | 0=True, 1=False | |
| BV | 15 | Module3UVLampChangeDue | Date on which UV lamp change is due for Module 3 | Write | 0=True, 1=False | |
| BV | 16 | Module4UVLampChangeDue | Date on which UV lamp change is due for Module 4 | Write | 0=True, 1=False | |
| BV | 17 | Module1CleaningChangeDue | Date on which cleaning is due for Module 1 | Write | 0=True, 1=False | |
| BV | 18 | Module2CleaningChangeDue | Date on which cleaning is due for Module 2 | Write | 0=True, 1=False | |
| BV | 19 | Module3CleaningChangeDue | Date on which cleaning is due for Module 3 | Write | 0=True, 1=False | |
| BV | 20 | Module4CleaningChangeDue | Date on which cleaning is due for Module 4 | Write | 0=True, 1=False | |
| BV | 21 | Module1Dilution | Water dilution cycle for Module 1 | Write | 0=Waiting, 1=In Progress | |
| BV | 22 | Module2Dilution | Water dilution cycle for Module 2 | Write | 0=Waiting, 1=In Progress | |
| BV | 23 | Module3Dilution | Water dilution cycle for Module 3 | Write | 0=Waiting, 1=In Progress | |
| BV | 24 | Module4Dilution | Water dilution cycle for Module 4 | Write | 0=Waiting, 1=In Progress | |
| BV | 25 | Module1ServiceWarning | Upcoming cleaning for Module 1 | Write | 0=OFF, 1=ON | |
| BV | 26 | Module2ServiceWarning | Upcoming cleaning for Module 2 | Write | 0=OFF, 1=ON | |
| BV | 27 | Module3ServiceWarning | Upcoming cleaning for Module 3 | Write | 0=OFF, 1=ON | |
| BV | 28 | Module4ServiceWarning | Upcoming cleaning for Module 4 | Write | 0=OFF, 1=ON | |
| BV | 29 | Module1ServiceAlarm | Alarm for Module 1 when cleaning, UV lamp change or Silver Ion... | Write | 0=OFF, 1=ON | |
| BV | 30 | Module2ServiceAlarm | Alarm for Module 2 when cleaning, UV lamp change or Silver Ion... | Write | 0=OFF, 1=ON | |
| BV | 31 | Module3ServiceAlarm | Alarm for Module 3 when cleaning, UV lamp change or Silver Ion... | Write | 0=OFF, 1=ON | |
| BV | 32 | Module4ServiceAlarm | Alarm for Module 4 when cleaning, UV lamp change or Silver Ion... | Write | 0=OFF, 1=ON | |
| BV | 33 | Module1DrainFault | Drain fault alarm for Module 1 when drain countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 34 | Module2DrainFault | Drain fault alarm for Module 2 when drain countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 35 | Module3DrainFault | Drain fault alarm for Module 3 when drain countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 36 | Module4DrainFault | Drain fault alarm for Module 4 when drain countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 37 | Module1WaterInletFault | Inlet fault for Module 1 when fill countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 38 | Module2WaterInletFault | Inlet fault for Module 2 when fill countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 39 | Module3WaterInletFault | Inlet fault for Module 3 when fill countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 40 | Module4WaterInletFault | Inlet fault for Module 4 when fill countdown reaches 0 | Write | 0=OFF, 1=ON | |
| BV | 41 | Module1WaterLevelDefect | Water level defect for Module 1 when both capacitive sensor and float... | Write | 0=OFF, 1=ON | |
| BV | 42 | Module2WaterLevelDefect | Water level defect for Module 2 when both capacitive sensor and float... | Write | 0=OFF, 1=ON | |
| BV | 43 | Module3WateLevelDefect | Water level defect for Module 3 when both capacitive sensor and float... | Write | 0=OFF, 1=ON | |
| BV | 44 | Module4WaterLevelDefect | Water level defect for Module 4 when both capacitive sensor and float... | Write | 0=OFF, 1=ON | |
| BV | 45 | Module1WaterTempDefect | Water temperature sensor defect for Module 1 | Write | 0=OFF, 1=ON | |
| BV | 46 | Module2WaterTempDefect | Water temperature sensor defect for Module 2.Module stops operation | Write | 0=OFF, 1=ON | |
| BV | 47 | Module3WaterTempDefect | Water temperature sensor defect for Module 3 | Write | 0=OFF, 1=ON | |
| BV | 48 | Module4WaterTempDefect | Water temperature sensor defect for Module 4 | Write | 0=OFF, 1=ON | |
| BV | 49 | Module1WaterLevelFault | Water level fault for Module 1 when capacitive level sensor is not... | Write | 0=OFF, 1=ON | |
| BV | 50 | Module2WaterLevelFault | Water level fault for Module 2 when capacitive level sensor is not... | Write | 0=OFF, 1=ON | |
| BV | 51 | Module3WateLevelFault | Water level fault for Module 3 when capacitive level sensor is not... | Write | 0=OFF, 1=ON | |
| BV | 52 | Module4WaterLevelFault | Water level fault for Module 4 when capacitive level sensor is not... | Write | 0=OFF, 1=ON | |
| BV | 53 | Module1HighWaterTemp | High water temperature for Module 1 when water temperature equals 25°C (77°F)... | Write | 0=OFF, 1=ON | |
| BV | 54 | Module2HighWaterTemp | High water temperature for Module 2 when water temperature equals 25°C (77°F)... | Write | 0=OFF, 1=ON | |
| BV | 55 | Module3HighWaterTemp | High water temperature for Module 3 when water temperature equals 25°C (77°F)... | Write | 0=OFF, 1=ON | |
| BV | 56 | Module4HighWaterTemp | High water temperature for Module 4 when water temperature equals 25°C (77°F)... | Write | 0=OFF, 1=ON | |
| BV | 57 | Module1HighWaterTempFault | High water temperature fault for Module 1 when Water temperature keeps at... | Write | 0=OFF, 1=ON | |
| BV | 58 | Module2HighWaterTempFault | High water temperature fault for Module 2 when Water temperature keeps at... | Write | 0=OFF, 1=ON | |
| BV | 59 | Module3HighWaterTempFault | High water temperature fault for Module 3 when Water temperature keeps at... | Write | 0=OFF, 1=ON | |
| BV | 60 | Module4HighWaterTempFault | High water temperature fault for Module 4 when Water temperature keeps at... | Write | 0=OFF, 1=ON | |
| BV | 61 | Module1FloatFault | Water float of Module 1 is in a fault condition | Write | 0=OFF, 1=ON | |
| BV | 62 | Module2FloatFault | Water float of Module 2 is in a fault condition | Write | 0=OFF, 1=ON | |
| BV | 63 | Module3FloatFault | Water float of Module 3 is in a fault condition | Write | 0=OFF, 1=ON | |
| BV | 64 | Module4FloatFault | Water float of Module 4 is in a fault condition | Write | 0=OFF, 1=ON | |
| BV | 65 | Module1CirculationPump | Circulation pump status of Module 1 | Write | 0=OFF, 1=ON | |
| BV | 66 | Module2CirculationPump | Circulation pump status of Module 2 | Write | 0=OFF, 1=ON | |
| BV | 67 | Module3CirculationPump | Circulation pump status of Module 3 | Write | 0=OFF, 1=ON | |
| BV | 68 | Module4CirculationPump | Circulation pump status of Module 4 | Write | 0=OFF, 1=ON | |
| BV | 69 | Module1FillValve | Fill valve status of Module 1 | Write | 0=OFF, 1=ON | |
| BV | 70 | Module2FillValve | Fill valve status of Module 2 | Write | 0=OFF, 1=ON | |
| BV | 71 | Module3FillValve | Fill valve status of Module 3 | Write | 0=OFF, 1=ON | |
| BV | 72 | Module4FillValve | Fill valve status of Module 4 | Write | 0=OFF, 1=ON | |
| BV | 73 | Module1Drain | Drain status of Module 1 | Write | 0=OFF, 1=ON | |
| BV | 74 | Module2Drain | Drain status of Module 2 | Write | 0=OFF, 1=ON | |
| BV | 75 | Module3Drain | Drain status of Module 3 | Write | 0=OFF, 1=ON | |
| BV | 76 | Module4Drain | Drain status of Module 4 | Write | 0=OFF, 1=ON | |
| BV | 77 | Module1StageValve1 | Status of Module 1's stage valve 1 | Write | 0=OFF, 1=ON | |
| BV | 78 | Module2StageValve1 | Status of Module 2's stage valve 1 | Write | 0=OFF, 1=ON | |
| BV | 79 | Module3StageValve1 | Status of Module 3's stage valve 1 | Write | 0=OFF, 1=ON | |
| BV | 80 | Module4StageValve1 | Status of Module 4's stage valve 1 | Write | 0=OFF, 1=ON | |
| BV | 81 | Module1StageValve2 | Status of Module 1's stage valve 2 | Write | 0=OFF, 1=ON | |
| BV | 82 | Module2StageValve2 | Status of Module 2's stage valve 2 | Write | 0=OFF, 1=ON | |
| BV | 83 | Module3StageValve2 | Status of Module 3's stage valve 2 | Write | 0=OFF, 1=ON | |
| BV | 84 | Module4StageValve2 | Status of Module 4's stage valve 2 | Write | 0=OFF, 1=ON | |
| BV | 85 | Module1StageValve3 | Status of Module 1's stage valve 3 | Write | 0=OFF, 1=ON | |
| BV | 86 | Module2StageValve3 | Status of Module 2's stage valve 3 | Write | 0=OFF, 1=ON | |
| BV | 87 | Module3StageValve3 | Status of Module 3's stage valve 3 | Write | 0=OFF, 1=ON | |
| BV | 88 | Module4StageValve3 | Status of Module 4's stage valve 3 | Write | 0=OFF, 1=ON | |
| BV | 89 | Module1StageValve4 | Status of Module 1's stage valve 4 | Write | 0=OFF, 1=ON | |
| BV | 90 | Module2StageValve4 | Status of Module 2's stage valve 4 | Write | 0=OFF, 1=ON | |
| BV | 91 | Module3StageValve4 | Status of Module 3's stage valve 4 | Write | 0=OFF, 1=ON | |
| BV | 92 | Module4StageValve4 | Status of Module 4's stage valve 4 | Write | 0=OFF, 1=ON | |
| BV | 93 | SimMode | Simulation mode state | Write | 0=OFF, 1=ON | |
| BV | 94 | SystInactivity | System inactivity state | Write | 0=True, 1=False | |
| BV | 95 | SystResetAlarms | Manual system reset alarm request | Write | 0=OFF, 1=ON | |
| BV | 96 | AirFlowCutout | Status is On when no air flow (AirFlowInput = opened) | Write | 0=OFF, 1=ON | |
| BV | 97 | HighLimitCutout | Status is On when too much humidity is present inside duct (HighLimitInput... | Write | 0=OFF, 1=ON | |
| BV | 98 | InterlockCutout | Status is On when InterlockInput = opened | Write | 0=OFF, 1=ON | |
| BV | 99 | RoomTempSensorDefect | Status is On when room temperature sensor is defective | Write | 0=OFF, 1=ON | |
| BV | 100 | RoomRHSensorDefect | Status is On when room relative humidity sensor is defective | Write | 0=OFF, 1=ON | |
| BV | 101 | DuctSensorDefect | Status is On when duct's relative humidity is defective | Write | 0=OFF, 1=ON | |
| BV | 102 | Module1CommTimeout | Status is On when communication is lost with Module 1 | Write | 0=OFF, 1=ON | |
| BV | 103 | Module2CommTimeout | Status is On when communication is lost with Module 2 | Write | 0=OFF, 1=ON | |
| BV | 104 | Module3CommTimeout | Status is On when communication is lost with Module 3 | Write | 0=OFF, 1=ON | |
| BV | 105 | Module4CommTimeout | Status is On when communication is lost with Module 4 | Write | 0=OFF, 1=ON | |
| BV | 106 | SystOutputLimited | Status is On when output is limited by any high limit signals | Write | 0=OFF, 1=ON | |
| BV | 107 | RunWhileServiceAlarm | When ON, modules will continue demand output even when their service alarm... | Write | 0=OFF, 1=ON | |
| BV | 108 | TempUnits | Available temperature unit options, °C and °F | Write | 0=°C, 1=°F | |
| BV | 109 | MassflowUnits | Available mass flow units, percent and mass flow | Write | 0=kg/h, 1=lb/h | |
| BV | 110 | OutputDisplay | Display of output in percent or mass flow units | Write | 0=Percent, 1=MassFlow | |
| BV | 111 | AlarmBeep | When the alarm beep is ON, any alarm sets the buzzer output... | Write | 0=OFF, 1=ON | |
| BV | 112 | KeyBeep | When the key beep is ON, the buzzer will beep to confirm... | Write | 0=OFF, 1=ON | |
| BV | 113 | OccupancySchedule | When the Occupancy Schedule status is ON and is in any internal... | Write | 0=OFF, 1=ON | |
| BV | 114 | TimeFormat | Available time format, 12 and 24 hours | Write | 0=24hr, 1=12hr | |
| BV | 115 | SilverIonNotif | When ON, the modules will notify when Silver Ion cartridge is due... | Write | 0=OFF, 1=ON | |
| BVmin | 116 | SystemPower | System normal operation when ON, produces humidity as per demand | Write | 0=OFF, 1=ON | |
| BV | 117 | WaterLevelCalibration | When ON, water level capacitive sensor will be automatically calibrated each time... | Write | 0=OFF, 1=ON | |
| BVmin | 118 | AlarmRelay | Closed when any alarm is on but AirFlowCutout and ServiceWarning | Write | 0=Opened, 1=Closed | |
| BV | 119 | MaitenanceRelay | Closed when ServiceAlarm or ServiceWarning is on | Write | 0=Opened, 1=Closed | |
| BV | 120 | Buzzer | ON when a key push event is acknowledge and KeyBeep is on... | Write | 0=OFF, 1=ON | |
| BVmin | 121 | NetworkFallbackAlarm | ON during a network fallback alarm | Write | 0=OFF, 1=ON | |
| BI | 1 | AirflowInput | Air flow switch input | Read | 0=Opened, 1=Closed | |
| BI | 2 | HighLimitInput | High limit switch input | Read | 0=Opened, 1=Closed | |
| BI | 3 | InterlockInput | Interlock cutout input | Read | 0=Opened, 1=Closed | |
| BI | 4 | DemandInput | Binary demand (all or nothing) input | Read | 0=Opened, 1=Closed | |
| BI | 5 | MemoryCard | Mounted when card is physically detected | Read | 0=Unmounted, 1=Mounted | |
| BI | 6 | Module1LowFloat | Low water level float state input for Module 1, closed when the... | Read | 0=Opened, 1=Closed | |
| BI | 7 | Module2LowFloat | Low water level float state input for Module 2, closed when the... | Read | 0=Opened, 1=Closed | |
| BI | 8 | Module3LowFloat | Low water level float state input for Module 3, closed when the... | Read | 0=Opened, 1=Closed | |
| BI | 9 | Module4LowFloat | Low water level float state input for Module 4, closed when the... | Read | 0=Opened, 1=Closed | |
| BI | 10 | Module1HighFloat | High water level float state input for Module 1, closed when the... | Read | 0=Opened, 1=Closed | |
| BI | 11 | Module2HighFloat | High water level float state input for Module 2, closed when the... | Read | 0=Opened, 1=Closed | |
| BI | 12 | Module3HighFloat | High water level float state input for Module 3, closed when the... | Read | 0=Opened, 1=Closed | |
| BI | 13 | Module4HighFloat | High water level float state input for Module 4, closed when the... | Read | 0=Opened, 1=Closed | |
| MV | 1 | HighLimitSource | Analog high limit source | Write | 1=None, 2=Analog Input 1, 3=Analog Input 2, 4=Analog Input 3, 5=Network | |
| MV | 2 | RoomTempSource | Room temperature source | Write | 1=None, 2=Analog Input 1, 3=Analog Input 2, 4=Analog Input 3, 5=Network | |
| MV | 3 | RoomRHSource | Room relative humidity source | Write | 1=None, 2=Analog Input 1, 3=Analog Input 2, 4=Analog Input 3, 5=Network | |
| MVmin | 4 | ControlMode | Control mode | Write | 1=Analog Input 1, 2=Analog Input 2, 3=Analog Input 3, 4=Internal Temperature, 5=Internal %RH, 6=Network | |
| MV | 5 | SetpointSource | Setpoint source | Write | 1=None, 2=Analog Input 1, 3=Analog Input 2, 4=Analog Input 3, 5=Internal, 6=Network | |
| MV | 6 | RoomTempSignal | Analog room temperature signal configuration | Write | 1=0-10Vdc, 2=2-10Vdc, 3=0-20mA, 4=4-20mA | |
| MV | 7 | RoomRHSignal | Analog room relative humidity signal configuration | Write | 1=0-10Vdc, 2=2-10Vdc, 3=0-20mA, 4=4-20mA | |
| MV | 8 | HighLimitSignal | Analog high limit signal configuration | Write | 1=0-10Vdc, 2=2-10Vdc, 3=0-20mA, 4=4-20mA | |
| MV | 9 | ControlSignal | External control signal configuration | Write | 1=0-10Vdc, 2=2-10Vdc, 3=0-20mA, 4=4-20mA | |
| MV | 10 | SetpointSignal | External setpoint signal configuration | Write | 1=0-10Vdc, 2=2-10Vdc, 3=0-20mA, 4=4-20mA | |
| MV | 11 | FeedbackSignal | Output feedback signal configuration | Write | 1=0-10Vdc, 2=2-10Vdc, 3=0-20mA, 4=4-20mA | |
| MV | 12 | SystemLanguage | Available language options, English and Francais | Write | 1=English, 2=Français | |
| MV | 13 | OccupancyState | Status of the Occupancy Schedule | Write | 1=Occupied, 2=Unoccupied, 3=Vacancy, 4=Off | |
| MV | 14 | AutoDrainState | Status of Auto Drain function | Write | 1=Wait, 2=Start, 3=Stop | |
| MV | 15 | AutoDrainConfig | Status of Auto Drain configuration | Write | 1=Interval, 2=Schedule | |
| MVmin | 16 | Module1State | Status of Module 1 | Write | 1=Stand-by, 2=Drain Cycle, 3=Disinfection Cycle, 4=Filling, 5=Ready, 6=Alarm | |
| MV | 17 | Module2State | Status of Module 2 | Write | 1=Stand-by, 2=Drain Cycle, 3=Disinfection Cycle, 4=Filling, 5=Ready, 6=Alarm | |
| MV | 18 | Module3State | Status of Module 3 | Write | 1=Stand-by, 2=Drain Cycle, 3=Disinfection Cycle, 4=Filling, 5=Ready, 6=alarm | |
| MV | 19 | Module4State | Status of Module 4 | Write | 1=Stand-by, 2=Drain Cycle, 3=Disinfection Cycle, 4=Filling, 5=Ready, 6=Alarm | |
| Other | 1 | ControllerUpdate | Firmware upgrade process available for the controller | Read | ||
| Other | 2 | Module1Update | Firmware upgrade process available for Module 1 | Read | ||
| Other | 3 | Module2Update | Firmware upgrade process available for Module 2 | Read | ||
| Other | 4 | Module3Update | Firmware upgrade process available for module 3 | Read | ||
| Other | 5 | Module4Update | Firmware upgrade process available for module 4 | Read | ||
| FILE | 1 | ControllerUpdate | File object of the controller firmware upgrade | Read | ||
| FILE | 2 | ControllerBootloaderUpdate | File object of the controller bootloader firmware upgrade | Read | ||
| FILE | 3 | ModuleUpdate | File object of the modules firmware upgrade | Read | ||
| FILE | 4 | ModuleBootloaderUpdate | File object of the modules bootloader firmware upgrade | Read | ||
| SCH | 1 | DrainSchedule | Weekly auto-drain schedule to specify when to manage auto-drain cycles | Write | ||
| SCH | 2 | OccupancySchedule | Weekly occupancy schedule to specify which occupancy state is active during specific... | Write |
No points match these filters.
Integration notes
- The guide's W? column lists Present Value for every object, so access here is inferred: inputs read-only, values writable.
- Module 2-4 objects only apply to multi-module systems.
- Temperature units follow the controller's Temperature Units setting.
Check it against the live device. A points list tells you what the controller can expose; the unit in front of you may differ by firmware or installed options. Easy BACnet scans a network for BACnet IP devices from an Android phone, reads every object on the SKV and exports what it actually has to Excel — free. New to BACnet? Start with what a BACnet points list is and what the object types mean.
Questions about the Neptronic SKV
How many BACnet points does the Neptronic SKV have?
This list has 277 BACnet objects: 13 analog inputs, 100 analog values, 13 binary inputs, 121 binary values, 4 files, 2 schedules, 19 multi-state values, 5 others. The exact set on a given unit depends on its firmware, installed options and configuration.
Which Neptronic SKV BACnet points are writable?
242 of the 277 objects accept a write. Points marked Command have a priority array: a write holds until it is released, so release it back to automatic when you are done. The source has no read/write column, so this is inferred from object type.
Where is the official Neptronic SKV BACnet documentation?
The source is SKV Evaporative Humidifier BACnet User Guide, revision 2018-09-05, published free by Neptronic at https://www.neptronic.com/Humidifiers/PDF/skv/20180905/SKV-BACnet-180905.pdf.
What are the minimum BACnet points to integrate the Neptronic SKV?
Start with BV 116 SystemPower (System power on/off); MV 4 ControlMode (Control mode (6 = Network)); AV 5 SystDemand (Demand from the BMS, % (when MSV 4 = Network)); AV 16 SetpointRH (BMS RH setpoint (when MSV 5 = Network)); AV 13 RoomRH (BMS room RH (when MSV 3 = Network)); MV 16 Module1State (Stand-by/drain/fill/ready/alarm state of module 1); AV 1 SystOutput (Actual system output %); BV 118 AlarmRelay (Closed on any alarm but airflow cutout/service warning); BV 121 NetworkFallbackAlarm (On when network values time out (AV 38)).
How do I enable BMS control of the Neptronic SKV?
BV 116 SystemPower: ON = normal operation, OFF = demand inhibited. MSV 4 ControlMode selects an analog input, internal temperature/RH control or Network.
Does the Neptronic SKV need a BACnet heartbeat or have a communication timeout?
AV 38 NetworkFallbackTimeout (1-15 min) applies whenever at least one control input uses Network as its source; AV 39 counts down and BV 121 NetworkFallbackAlarm turns on when it expires.
Can the BMS supply sensor values to the Neptronic SKV?
Set MSV 3 RoomRHSource or MSV 2 RoomTempSource to Network and write the values from the BMS; MSV 5 SetpointSource = Network uses the external setpoints AV 16 (RH) and AV 17 (temperature).
How do I check these points on the real SKV?
Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.
More Neptronic BACnet points lists
- Make-up air unit (electric heat)
Neptronic CMU Compact Make-up Air Unit
Neptronic CMU compact make-up air units with electric heating, EC fan, damper and optional exhaust fan outputs.
Also known as: CMU, Neptronic CMU - Fan coil unit controller
Neptronic EFCB Series Fan Coil Controller
Neptronic EFCB fan coil controllers (24, 120 or 240 Vac, 2 or 4 relays) for 2-pipe and 4-pipe fan coils with TFL/TDF room sensors.
Also known as: EFCB, EFCB10TU2, EFCB10TU4, EFCB11TU2, EFCB11TU4, EFCB12TU2, EFCB12TU4 - Fan coil unit controller
Neptronic EFCB-OE1 Series Fan Coil Controller
Neptronic EFCB-OE1 fan coil controllers (24 or 240 Vac, 0, 2 or 4 relays), an OEM variant of the EFCB series.
Also known as: EFCB-OE1, EFCB10T-OE1, EFCB12T-OE1, EFCB12TU2-OE1, EFCB12TU4-OE1 - VAV terminal unit controller
Neptronic EVCB14N Series VAV Controller
Neptronic EVCB14N networkable VAV controllers with integrated damper actuator, pressure-independent or pressure-dependent, with 0-4 triac outputs.
Also known as: EVCB14N, EVCB14NIT0S, EVCB14NIT2S, EVCB14NIT4S, EVCB14NDT4S, EVCB14NIT0SF, EVCB14NIT4SF - VAV terminal unit controller
Neptronic EVCB14NxT4X VAV Controller (external motor)
Neptronic EVCB14N VAV controllers with four triac outputs that drive an external damper motor, pressure independent (IT4X) or dependent (DT4X).
Also known as: EVCB14NxT4X, EVCB14NIT4X, EVCB14NDT4X - VAV terminal unit controller
Neptronic EVCB44N Series VAV Controller
Neptronic EVCB44N VAV controllers without triac outputs, pressure independent (IT0S) or pressure dependent (DT0S).
Also known as: EVCB44N, EVCB44NIT0S, EVCB44NDT0S - Dual duct VAV terminal controller
Neptronic EVCBM Dual Duct VAV Controller
Neptronic EVCBM master controller used on dual duct terminals, with a second (slave) airflow channel for the other duct.
Also known as: EVCBM, EVCBM Dual Duct, EVCB dual duct - Steam humidifier valve controller
Neptronic SKDESC-xB
Neptronic SKDESC-xB electronic controllers for steam-to-steam / direct steam injection humidifier valves (ESCJx jacketed, ESCMx models).
Also known as: SKDESC, SKDESCxB, ESCJx, ESCMx, Electronic Steam Controller - Electric steam humidifier
Neptronic SKE4
Neptronic SKE4 electric (heating element) steam humidifiers, indoor and outdoor versions.
Also known as: SKE4 electric steam humidifier, SKE4-N, SKE4-E, SKE4 BACnet - Gas-fired steam humidifier
Neptronic SKG4
Neptronic SKG4 gas-fired steam humidifiers with up to four humidifier modules.
Also known as: SKG4 gas fired humidifier, SKG4-N, SKG4-E, SKG4 BACnet - High-pressure atomizing humidifier / cooler
Neptronic SKH4
Neptronic SKH4 high-pressure water atomizing humidifiers and evaporative coolers with up to six zones (A-F).
Also known as: SKH4 high-pressure atomizer, SKH4 BACnet - Reverse osmosis water treatment unit
Neptronic SKRO
Neptronic SKRO reverse osmosis water treatment units feeding humidifiers.
Also known as: SKRO reverse osmosis, SKRO BACnet - Steam-to-steam humidifier
Neptronic SKS4
Neptronic SKS4 steam-to-steam (boiler steam heated) humidifiers.
Also known as: SKS4 steam to steam humidifier, SKS4 BACnet - Evaporative cooler / humidifier
Neptronic SKVF
Neptronic SKVF series evaporative coolers (also used for humidification).
Also known as: SKVF evaporative cooler, SKVF Series, SKVF BACnet - Fan coil / zone thermostat controller
Neptronic TFxB Series Thermostat Controller
Neptronic TFxB24 communicating thermostats for 2-pipe and 4-pipe fan coils and zone heating/cooling, including the humidity (TFHB) and OE variants.
Also known as: TFCB24F3XYZ1, TFCB24F3XY2, TFHB24F3XYZ1, TFHB24F3XYZ2, TFCB24P3-OE1, TFHB24P3-OE1, TFHB24P3-OE2, TFxB24
Source: SKV Evaporative Humidifier BACnet User Guide · rev. 2018-09-05. Object names, instances and units are reproduced as published; descriptions are our own.