Easy BACnet- Home
- BACnet points lists
- Fulton
- Siemens LMV36 with BACnet Interface
Boiler burner control · BACnet points list
Fulton Siemens LMV36 with BACnet Interface BACnet points list
Updated 6 November 2026
Fulton lists 21 objects for a boiler with a Siemens LMV36 burner control on a BACnet interface. Analog Inputs 1-18 report output, flame signal and the state of the controller, safety loop, gas pressure switches, alarm, ignition, fan and fuel valves (as 0/1 integers), plus remote mode and fuel. Analog Values 19-21 let the BMS take remote control and set an output.
This page lists 21 BACnet objects for the Fulton Siemens LMV36 with BACnet Interface — 3 of them writable — with each object’s type, instance number, name, engineering units and access. It is re-typed from Fulton’s own free documentation, linked below.
- Manufacturer
- Fulton
- Model
- Siemens LMV36 with BACnet Interface
- Equipment
- Boiler burner control
- Equipment type
- Boilers & water heaters
- BACnet objects
- 21 (3 writable)
- Transport
- —
- Firmware
- Not stated
- Also known as
- LMV36, Siemens LMV36, LMV3, Fulton LMV36
- Source document
- Network Addressing - LMV36 with A BACnet Interface
Reference only, provided as-is: verify against Fulton’s current documentation and the live device before use. Not official Fulton information. Terms of use.
BMS integration notes: Fulton Siemens LMV36 with BACnet Interface
Write Modbus Mode = Remote (AV 19), then Operating Mode in Remote (AV 20: Auto, Remote On, Remote Off) and the Predefined Output (AV 21). Read current output, flame signal, the alarm input and the switch states.
Minimum points to map
The short list most integrators start with — enough to run the unit from a BMS. Map more as the job needs.
| Object | Name | Why | Access |
|---|---|---|---|
| AV 20 | Operating Mode in Remote | 0 = Auto, 1 = Remote On, 2 = Remote Off | Write |
| AV 19 | Modbus Mode | Set 1 = Remote so network commands take effect | Write |
| AV 21 | Predefined Output Modulation (Modulation Rate) | Output in remote, 200-1000 | Write |
| AI 3 | Controller On/Off | Controller on/off; 0 = On, 1 = Off | Read |
| AI 1 | Current Output | Current burner output, % | Read |
| AI 2 | Flame Signal | Flame signal, % | Read |
| AI 9 | Alarm | Alarm; 0 = On, 1 = Off | Read |
Enable & remote start
AV 19 Modbus Mode = 1 (Remote) hands control to the network; AV 20 Operating Mode in Remote selects 0 = Auto, 1 = Remote On or 2 = Remote Off, and AV 21 Predefined Output Modulation sets the output (200-1000).
Network setup
- Object IDs 1-21 are fixed.
- The sheet gives no device instance, MAC address or baud rate.
Watch out for
- Switch and output states are Analog Inputs with 0 = On, 1 = Off (inverted from the usual binary convention).
- AI 15-17 are read-only copies of the writable AV 19-21.
Fulton Siemens LMV36 with BACnet Interface BACnet objects
Type: AI, AO, AV, BI, BO, BV, MI/MO/MV (multi-state) · Access: Read read-only, Write writable, Command writable with a priority array.
| Description | States | |||||
|---|---|---|---|---|---|---|
| AImin | 1 | Current Output | Range 0 - 100% | Read | ||
| AImin | 2 | Flame Signal | Range 0 - 100% | Read | ||
| AImin | 3 | Controller On/Off | Read | 0=On, 1=Off | ||
| AI | 4 | Pressure Valve Prove | Read | 0=On, 1=Off | ||
| AI | 5 | Safety Loop | Read | 0=On, 1=Off | ||
| AI | 6 | DW Min | Read | 0=On, 1=Off | ||
| AI | 7 | DW Max | Read | 0=On, 1=Off | ||
| AI | 8 | Air Pressure Switch | Read | 0=On, 1=Off | ||
| AImin | 9 | Alarm | Read | 0=On, 1=Off | ||
| AI | 10 | Ignition | Read | 0=On, 1=Off | ||
| AI | 11 | Fan | Read | 0=On, 1=Off | ||
| AI | 12 | Fuel V1 | Read | 0=On, 1=Off | ||
| AI | 13 | Fuel V2 | Read | 0=On, 1=Off | ||
| AI | 14 | Fuel V3 | Read | 0=On, 1=Off | ||
| AI | 15 | Modbus Mode | Read | 0=Local, 1=Remote | ||
| AI | 16 | Operating Mode in Remote | Read | 0=Auto, 1=Remote On, 2=Remote Off | ||
| AI | 17 | Predefined Output Modulation (Modulation Rate) | Range 200 - 1000 | Read | ||
| AI | 18 | Current Fuel Mode | Read | 0=Gas, 1=Oil | ||
| AVmin | 19 | Modbus Mode | Write | 0=Local, 1=Remote | ||
| AVmin | 20 | Operating Mode in Remote | Write | 0=Auto, 1=Remote On, 2=Remote Off | ||
| AVmin | 21 | Predefined Output Modulation (Modulation Rate) | Range 200 - 1000 | Write |
No points match these filters.
Object ID lookup: Fulton Siemens LMV36 with BACnet Interface point IDs by name
AI1Current OutputAI2Flame SignalAI3Controller On/OffAI4Pressure Valve ProveAI5Safety LoopAI6DW MinAI7DW MaxAI8Air Pressure SwitchAI9AlarmAI10IgnitionAI11FanAI12Fuel V1AI13Fuel V2AI14Fuel V3AI15Modbus ModeAI16Operating Mode in RemoteAI17Predefined Output Modulation (Modulation Rate)AI18Current Fuel ModeAV19Modbus ModeAV20Operating Mode in RemoteAV21Predefined Output Modulation (Modulation Rate)
Integration notes
- All monitoring objects are Analog Inputs with integer values; 0 = On and 1 = Off for the switch states.
- The sheet does not say which gateway or transport is used.
Check it against the live device. A points list tells you what the controller can expose; the unit in front of you may differ by firmware or installed options. This list is provided as-is for reference only and may contain mistakes — confirming it before you write, map or commission anything is up to you (terms). Easy BACnet scans a network for BACnet IP devices from an Android phone, reads every object on the Siemens LMV36 with BACnet Interface and exports what it actually has to Excel — free. New to BACnet? Start with what a BACnet points list is and what the object types mean.
Questions about the Fulton Siemens LMV36 with BACnet Interface
How many BACnet points does the Fulton Siemens LMV36 with BACnet Interface have?
This list has 21 BACnet objects: 18 analog inputs, 3 analog values. The exact set on a given unit depends on its firmware, installed options and configuration.
Which Fulton Siemens LMV36 with BACnet Interface BACnet points are writable?
3 of the 21 objects accept a write. Points marked Command have a priority array: a write holds until it is released, so release it back to automatic when you are done.
Where is the official Fulton Siemens LMV36 with BACnet Interface BACnet documentation?
The source is Network Addressing - LMV36 with A BACnet Interface, published free by Fulton at https://fulton.com/app/uploads/2021/02/BACnet_PointsList_LMV36.pdf.
What are the minimum BACnet points to integrate the Fulton Siemens LMV36 with BACnet Interface?
Start with AV 20 Operating Mode in Remote (0 = Auto, 1 = Remote On, 2 = Remote Off); AV 19 Modbus Mode (Set 1 = Remote so network commands take effect); AV 21 Predefined Output Modulation (Modulation Rate) (Output in remote, 200-1000); AI 3 Controller On/Off (Controller on/off; 0 = On, 1 = Off); AI 1 Current Output (Current burner output, %); AI 2 Flame Signal (Flame signal, %); AI 9 Alarm (Alarm; 0 = On, 1 = Off).
How do I enable BMS control of the Fulton Siemens LMV36 with BACnet Interface?
AV 19 Modbus Mode = 1 (Remote) hands control to the network; AV 20 Operating Mode in Remote selects 0 = Auto, 1 = Remote On or 2 = Remote Off, and AV 21 Predefined Output Modulation sets the output (200-1000).
How do I check these points on the real Siemens LMV36 with BACnet Interface?
Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.
More Fulton BACnet points lists
- Boiler burner control gateway
Fulton Boiler with Siemens LMV3 (N54 ProtoNode)
Fulton boilers with a Siemens LMV3 burner management control, read through Fulton's N54 ProtoNode gateway.
Also known as: LMV3, LMV 3, Siemens LMV3, N54 ProtoNode, Fulton ProtoNode - Boiler burner control gateway
Fulton Boiler with Siemens LMV3 and Yokogawa UT32A (N54 ProtoNode)
Fulton hydronic boilers with a Siemens LMV3 burner control and a Yokogawa UT32A temperature controller, read through the N54 ProtoNode.
Also known as: LMV3, Siemens LMV3, Yokogawa UT32A, UT32A, N54 ProtoNode - Boiler plant sequencer
Fulton Hydronic ModSync SE v6.6.1.X (N54 ProtoNode)
Fulton ModSync SE hydronic boiler sequencer (software 6.6.1.X) managing up to 8 boilers, read through the N54 ProtoNode.
Also known as: ModSync, ModSync SE, Fulton ModSync, ModSync sequencer, N54 ProtoNode - Boiler controller gateway
Fulton Hydronic SOLA Boiler (N54 ProtoNode)
Fulton hydronic boilers with the SOLA burner control, one block of objects per boiler on the N54 ProtoNode.
Also known as: SOLA, Fulton SOLA, Honeywell SOLA, N54 ProtoNode - Boiler plant controller gateway
Fulton Hydronic SOLA Master (lead/lag) (N54 ProtoNode)
The SOLA lead/lag master of a group of Fulton hydronic boilers (up to 8 slaves), read through the N54 ProtoNode.
Also known as: SOLA Master, Fulton SOLA lead lag, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura EDR 750-2000 Provider (N54 ProtoNode)
The Provider (lead) boiler of a Fulton Endura (EDR) 750-2000 hydronic lead/lag group with the PURE control, read through the N54 ProtoNode.
Also known as: Endura, EDR 750, EDR 2000, EDR 2MM, Fulton PURE Provider, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura EDR 750-2000 Single (N54 ProtoNode)
Fulton Endura (EDR) 750-2000 hydronic boilers with the PURE control, one boiler per address block on the N54 ProtoNode.
Also known as: Endura, EDR 750, EDR 2000, EDR 2MM, Fulton PURE, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura XE EXE 399-750 Provider (N54 ProtoNode)
The Provider (lead) boiler of a Fulton Endura XE (EXE) 399-750 hydronic lead/lag group with the PURE control, read through the N54 ProtoNode.
Also known as: Endura XE, EXE 399, EXE 750, Fulton PURE Provider, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura XE EXE 399-750 Single (N54 ProtoNode)
Fulton Endura XE (EXE) 399-750 hydronic boilers with the PURE control, one boiler per address block on the N54 ProtoNode.
Also known as: Endura XE, EXE 399, EXE 750, Fulton PURE, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura ZE Provider (N54 ProtoNode)
The Provider (lead) boiler of a Fulton Endura (EDR) ZE lead/lag group with the PURE control, read through the N54 ProtoNode.
Also known as: Endura ZE, EDR ZE, Fulton PURE Provider, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura ZE Single (N54 ProtoNode)
Fulton Endura (EDR) ZE boilers with the PURE control, one boiler per address block on the N54 ProtoNode.
Also known as: Endura ZE, EDR ZE, Fulton PURE, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura+ EDR+ 2500-6000 (N54 ProtoNode)
Fulton hydronic boilers run by the PURE control (the file name points to Endura+ EDR+ 2500-6000 MBH sizes), read through the N54 ProtoNode.
Also known as: PURE, Fulton PURE, Endura+, EDR+, Endura Plus, Hydronic PURE, N54 ProtoNode - Boiler controller gateway
Fulton PURE Control - Endura+ EDR+ 2500-6000 Provider (N54 ProtoNode)
The Provider (lead) boiler of a Fulton Endura+ (EDR+) 2500-6000 hydronic lead/lag group with the PURE control, read through the N54 ProtoNode.
Also known as: Endura+, EDR+, Endura Plus, EDR+ 2500, EDR+ 6000, Fulton PURE Provider, N54 ProtoNode - Steam boiler controller gateway
Fulton PURE Control - VSRT Steam Boiler Provider (N54 ProtoNode)
The Provider (lead) boiler of a Fulton VSRT steam boiler lead/lag group with the PURE control, read through the N54 ProtoNode.
Also known as: VSRT, Fulton VSRT, Steam PURE Provider, N54 ProtoNode - Steam boiler controller gateway
Fulton PURE Control - VSRT Steam Boiler Single (N54 ProtoNode)
Fulton VSRT steam boilers with the PURE control, one boiler per address block on the N54 ProtoNode.
Also known as: VSRT, Fulton VSRT, Steam PURE, Fulton PURE, N54 ProtoNode - Steam boiler burner control
Fulton Siemens LMV5 Steam Boiler with BACnet Interface
Fulton steam boilers whose Siemens LMV5 burner management is given a BACnet interface (standard configurations).
Also known as: LMV5, Siemens LMV5, LMV52, Fulton LMV5 - Steam boiler plant sequencer
Fulton Steam ModSync SE v6.6.1.0 (ProtoNode)
Fulton ModSync SE steam boiler sequencer (version 6.6.1.0) managing up to 8 steam boilers, read through a Sierra Monitor ProtoNode.
Also known as: ModSync SE, ModSync, Fulton ModSync steam, ProtoNode
Source: Network Addressing - LMV36 with A BACnet Interface. Object names, instances and units are reproduced as published; descriptions are our own.