Easy BACnet- Home
- BACnet points lists
- CaptiveAire
- MUA Heater DDC (Protocessor BACnet)
Make-up air unit controller · BACnet points list
CaptiveAire MUA Heater DDC (Protocessor BACnet) BACnet points list
Updated 28 October 2026
CaptiveAire make-up air heaters with the DDC package expose their unit-board data through a factory gateway for BACnet IP or MS/TP. The 161 objects include DDC heat/cool/blower commands, tempering and activation modes, occupied/unoccupied setpoints and blower/damper limits, a 42-point on-board schedule, sensor readings, occupancy flags and six active fault codes. As with the Paragon RTUs, the preferred BMS approach is setpoints plus the DDC Occupied Override binary rather than the raw DDC commands.
This page lists 161 BACnet objects for the CaptiveAire MUA Heater DDC (Protocessor BACnet) — 118 of them writable — with each object’s type, instance number, name, engineering units and access. It is re-typed from CaptiveAire’s own free documentation, linked below.
- Manufacturer
- CaptiveAire
- Model
- MUA Heater DDC (Protocessor BACnet)
- Equipment
- Make-up air unit controller
- Equipment type
- Rooftop units, AHUs & DOAS
- BACnet objects
- 161 (118 writable)
- Transport
- BACnet IP, BACnet MS/TP
- Firmware
- Not stated
- Default device instance
- 50000
- Also known as
- CaptiveAire make-up air, Direct fired MUA, Tempered make-up air, DDC Application Guide MUA
- Source document
- DDC Application Guide for MUA Heater Units · rev. 2024-10
BMS integration notes: CaptiveAire MUA Heater DDC (Protocessor BACnet)
Enable scheduling once (BV-8), set all on-board schedule slots (AV-61..102) to 1440, then drive occupancy from the BMS with BV-7 DDCOccupiedOverride and let the unit temper to its own setpoints. The guide calls setpoint adjustment plus the occupied override the preferred method; the DDC heat/cool/blower commands are only for jobs where the tempering modes are set to DDC. Monitor HVAC state, occupancy flags, temperatures and the six fault-code AIs.
Minimum points to map
The short list most integrators start with — enough to run the unit from a BMS. Map more as the job needs.
| Object | Name | Why | Access |
|---|---|---|---|
| BV 7 | DDCOccupiedOverride | Occupied/unoccupied command from the BMS | Write |
| BV 8 | SchedulingEnabled | Must be on (once) for BV-7 to work | Write |
| AV 45 | DischargeHeatOccSP | Occupied discharge heating setpoint | Write |
| AI 143 | CurrentHvacState | Idle / blower / heating / cooling state | Read |
| AI 148 | CurrentOccupiedStatus | Confirms the occupancy command took effect | Read |
| AI 121 | DischargeStatTemp | Discharge air temperature | Read |
| AI 154 | GasValveOutput | Burner modulation level | Read |
| AI 137 | ActiveFault1Id | First active fault code | Read |
Enable & remote start
BV-8 SchedulingEnabled must be on and the internal schedule AVs (61-102) all set to 1440 so BV-7 has full control of occupancy. DDC commands (BV-1..5, AV-6) work only with the heat/cool tempering modes (AV-9..12) set to DDC; this disables temperature-based activation and heat and cool cannot be called together.
Network setup
- Protocessor default device instance 50000, MS/TP MAC 127, 38400 baud; default IP 192.168.1.24 /255.255.255.0.
- Web configurator login admin/admin, or the password printed by the gateway's Ethernet port; each change needs Submit and a restart.
- The gateway is factory set to BACnet IP or MS/TP for the job; only that port carries BACnet.
Watch out for
- Factory setting points (modes, limits) should not be written on a regular basis.
- SchedulingEnabled only allows scheduling; it is not an occupancy command.
- Schedule values are minutes after midnight (0-1439); 1440 means no schedule, and both start and end of a set must be 1440.
- The controller board reboots when some factory settings are changed.
CaptiveAire MUA Heater DDC (Protocessor BACnet) BACnet objects
Type: AI, AO, AV, BI, BO, BV, MI/MO/MV (multi-state) · Access: Read read-only, Write writable, Command writable with a priority array.
| Description | States | |||||
|---|---|---|---|---|---|---|
| BV | 1 | DDCHeatCommand | Heating command, requires heat tempering mode = DDC | Write | ||
| BV | 2 | DDCCoolCommand1 | Cooling stage 1 command, requires cool tempering mode = DDC | Write | ||
| BV | 3 | DDCCoolCommand2 | Cooling stage 2 command, requires cool tempering mode = DDC | Write | ||
| BV | 4 | DDCCoolCommand3 | Cooling stage 3 command, requires cool tempering mode = DDC | Write | ||
| BV | 5 | DDCBlowerCommand | Blower command, requires both heat and cool tempering modes = DDC | Write | ||
| AV | 6 | DDCHeatModulation | Heat modulation signal, 0-10V. 0V = low fire and 10V = high | Write | ||
| BVmin | 7 | DDCOccupiedOverride | Occupied override command, requires SchedulingEnabled = ON (1) | Write | ||
| BVmin | 8 | SchedulingEnabled | Enable scheduling | Write | ||
| AV | 9 | HeatTemperModeOcc | Heat tempering mode during occupied time | Write | 0=Discharge, 1=Space, 2=BAS, 3=DDC | |
| AV | 10 | HeatTemperModeUnocc | Heat tempering mode during unoccupied time | Write | 0=Discharge, 1=Space, 2=BAS, 3=DDC | |
| AV | 11 | CoolTemperModeOcc | Cool tempering mode during occupied time | Write | 0=Intake, 1=Space, 2=BAS, 3=DDC | |
| AV | 12 | CoolTemperModeUnocc | Cool tempering mode during unoccupied time | Write | 0=Intake, 1=Space, 2=BAS, 3=DDC | |
| AV | 13 | ActivateOnOcc | "Activate based on" during occupied time | Write | 0=Intake, 1=Space, 2=Both, 3=Either, 4=Stat | |
| AV | 14 | ActivateOnUnocc | "Activate based on" during unoccupied time | Write | 0=Intake, 1=Space, 2=Both, 3=Either, 4=Stat | |
| AV | 15 | SpaceHeatHyst | Space Heating Hysteresis | Write | ||
| AV | 16 | IntakeHeatHyst | Intake Heating Hysteresis | Write | ||
| AV | 17 | SpaceCoolHyst | Space Cooling Hysteresis | Write | ||
| AV | 18 | IntakeCoolHyst | Intake Cooling Hysteresis | Write | ||
| AV | 19 | EvapHyst | Evap Cooling Hysteresis | Write | ||
| AV | 20 | BlowerModeOcc | Blower mode during occupied times | Write | 0=Auto, 1=Off, 2=On | |
| AV | 21 | BlowerModeUnocc | Blower mode during unoccupied times | Write | 0=Auto, 1=Off, 2=On | |
| AV | 22 | MixingBoxMode | Mixing box mode | Write | 0=Off, 1=Manual, 2=2 Position, 3=OA Percent, 4=Analog Ctrl, 5=PS, 6=100% OA, 7=Modes | |
| AV | 23 | MixingBoxMinOAPercentOcc | Min occupied outdoor air percent when mixing box mode = outdoor air | Write | ||
| AV | 24 | MixingBoxMinOAPercentUnocc | Min unoccupied outdoor air percent when mixing box mode = outdoor air | Write | ||
| AV | 25 | MixingBoxMaxOAPercentOcc | Max occupied outdoor air percent when mixing box mode = outdoor air | Write | ||
| AV | 26 | MixingBoxMaxOAPercentUnocc | Max unoccupied outdoor air percent when mixing box mode = outdoor air | Write | ||
| AV | 27 | MixingBoxMinVoltsOcc | Min occupied mixing box voltage when mixing box mode = manual | Write | ||
| AV | 28 | MixingBoxMinVoltsUnocc | Min unoccupied mixing box voltage when mixing box mode = manual | Write | ||
| AV | 29 | MixingBoxMaxVoltsOcc | Max occupied mixing box voltage when mixing box mode = manual | Write | ||
| AV | 30 | MixingBoxMaxVoltsUnocc | Max unoccupied mixing box voltage when mixing box mode = manual | Write | ||
| AV | 31 | BlowerVFDMinFreqOcc | Min blower VFD Frequency when occupied | Write | ||
| AV | 32 | BlowerVFDMinFreqUnocc | Min blower VFD Frequency when unoccupied | Write | ||
| AV | 33 | BlowerVFDMaxFreqOcc | Max blower VFD Frequency when occupied | Write | ||
| AV | 34 | BlowerVFDMaxFreqUnocc | Max blower VFD Frequency when unoccupied | Write | ||
| AV | 35 | BlowerPWMMinOcc | Min blower ECM speed when occupied | Write | ||
| AV | 36 | BlowerPWMMinUnocc | Min blower ECM speed when unoccupied | Write | ||
| AV | 37 | BlowerPWMMaxOcc | Max blower ECM speed when occupied | Write | ||
| AV | 38 | BlowerPWMMaxUnocc | Max blower ECM speed when unoccupied | Write | ||
| AV | 39 | IntakeHeatOccSP | Intake Heating Occupied Setpoint | Write | ||
| AV | 40 | IntakeHeatUnoccSP | Intake Heating Unoccupied Setpoint | Write | ||
| AV | 41 | SpaceHeatOccSP | Space Heating Occupied Setpoint | Write | ||
| AV | 42 | SpaceHeatUnoccSP | Space Heating Unoccupied Setpoint | Write | ||
| AV | 43 | MinDischargeHeatOccSP | Min Discharge Heating when occupied, relevant only if heat tempering mode = | Write | ||
| AV | 44 | MinDischargeHeatUnoccSP | Min Discharge Heating when unoccupied, relevant only if heat tempering mode = | Write | ||
| AVmin | 45 | DischargeHeatOccSP | Discharge heating setpoint when occupied, requires heat tempering mode = discharge | Write | ||
| AV | 46 | DischargeHeatUnoccSP | Discharge heating setpoint when unoccupied, requires heat tempering mode = discharge | Write | ||
| AV | 47 | MaxDischargeHeatOccSP | Max Discharge Heating when occupied, relevant only if heat tempering mode = | Write | ||
| AV | 48 | MaxDischargeHeatUnoccSP | Max Discharge Heating when unoccupied, relevant only if heat tempering mode = | Write | ||
| AV | 49 | IntakeCoolOccSP | Intake Cooling Occupied Setpoint | Write | ||
| AV | 50 | IntakeCoolUnoccSP | Intake Cooling Unoccupied Setpoint | Write | ||
| AV | 51 | SpaceCoolOccSP | Space Cooling Occupied Setpoint | Write | ||
| AV | 52 | SpaceCoolUnoccSP | Space Cooling Unoccupied Setpoint | Write | ||
| AV | 53 | IntakeCoolStagingDiffOcc | Intake Cooling Stage Differential Setpoint when occupied | Write | ||
| AV | 54 | IntakeCoolStagingDiffUnocc | Intake Cooling Stage Differential Setpoint when unoccupied | Write | ||
| AV | 55 | SpaceCoolStagingDiffOcc | Space Cooling Stage Differential Setpoint when occupied | Write | ||
| AV | 56 | SpaceCoolStagingDiffUnocc | Space Cooling Stage Differential Setpoint when unoccupied | Write | ||
| AV | 57 | RoomOverrideOccSP | Room Override Occupied Setpoint | Write | ||
| AV | 58 | RoomOverrideUnoccSP | Room Override Unoccupied Setpoint | Write | ||
| AV | 59 | OAEvapCoolOccSP | Outdoor air evap cooling occupied setpoint | Write | ||
| AV | 60 | OAEvapCoolUnoccSP | Outdoor air evap cooling unoccupied setpoint | Write | ||
| AV | 61 | ScheduleSundayAStart | Daily schedule start/end time in minutes | Write | ||
| AV | 62 | ScheduleSundayAEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 63 | ScheduleSundayBStart | Daily schedule start/end time in minutes | Write | ||
| AV | 64 | ScheduleSundayBEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 65 | ScheduleSundayCStart | Daily schedule start/end time in minutes | Write | ||
| AV | 66 | ScheduleSundayCEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 67 | ScheduleMondayAStart | Daily schedule start/end time in minutes | Write | ||
| AV | 68 | ScheduleMondayAEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 69 | ScheduleMondayBStart | Daily schedule start/end time in minutes | Write | ||
| AV | 70 | ScheduleMondayBEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 71 | ScheduleMondayCStart | Daily schedule start/end time in minutes | Write | ||
| AV | 72 | ScheduleMondayCEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 73 | ScheduleTuesdayAStart | Daily schedule start/end time in minutes | Write | ||
| AV | 74 | ScheduleTuesdayAEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 75 | ScheduleTuesdayBStart | Daily schedule start/end time in minutes | Write | ||
| AV | 76 | ScheduleTuesdayBEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 77 | ScheduleTuesdayCStart | Daily schedule start/end time in minutes | Write | ||
| AV | 78 | ScheduleTuesdayCEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 79 | ScheduleWednesdayAStart | Daily schedule start/end time in minutes | Write | ||
| AV | 80 | ScheduleWednesdayAEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 81 | ScheduleWednesdayBStart | Daily schedule start/end time in minutes | Write | ||
| AV | 82 | ScheduleWednesdayBEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 83 | ScheduleWednesdayCStart | Daily schedule start/end time in minutes | Write | ||
| AV | 84 | ScheduleWednesdayCEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 85 | ScheduleThursdayAStart | Daily schedule start/end time in minutes | Write | ||
| AV | 86 | ScheduleThursdayAEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 87 | ScheduleThursdayBStart | Daily schedule start/end time in minutes | Write | ||
| AV | 88 | ScheduleThursdayBEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 89 | ScheduleThursdayCStart | Daily schedule start/end time in minutes | Write | ||
| AV | 90 | ScheduleThursdayCEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 91 | ScheduleFridayAStart | Daily schedule start/end time in minutes | Write | ||
| AV | 92 | ScheduleFridayAEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 93 | ScheduleFridayBStart | Daily schedule start/end time in minutes | Write | ||
| AV | 94 | ScheduleFridayBEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 95 | ScheduleFridayCStart | Daily schedule start/end time in minutes | Write | ||
| AV | 96 | ScheduleFridayCEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 97 | ScheduleSaturdayAStart | Daily schedule start/end time in minutes | Write | ||
| AV | 98 | ScheduleSaturdayAEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 99 | ScheduleSaturdayBStart | Daily schedule start/end time in minutes | Write | ||
| AV | 100 | ScheduleSaturdayBEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 101 | ScheduleSaturdayCStart | Daily schedule start/end time in minutes | Write | ||
| AV | 102 | ScheduleSaturdayCEnd | Daily schedule start/end time in minutes | Write | ||
| AV | 103 | BlowerManualFreqOcc | VFD frequency when occupied, requires blower control = VFD manual | Write | ||
| AV | 104 | BlowerManualFreqUnocc | VFD frequency when unoccupied, requires blower control = VFD manual | Write | ||
| AV | 105 | BlowerManualPwmRateOcc | ECM speed when occupied, requires blower control = ECM manual | Write | ||
| AV | 106 | BlowerManualPwmRateUnocc | ECM speed when unoccupied, requires blower control = ECM manual | Write | ||
| AV | 107 | MixingBoxManualOAOcc | Mixing Box Outdoor Air Percent during occupied times, requires mixing box mode | Write | ||
| AV | 108 | MixingBoxManualOAUnocc | Mixing Box Outdoor Air Percent during unoccupied times, requires mixing box mode | Write | ||
| AV | 109 | MixingBoxManualVoltsOcc | Mixing Box damper voltage during occupied times, requires mixing box mode = | Write | ||
| AV | 110 | MixingBoxManualVoltsUnocc | Mixing Box damper voltage during unoccupied times, requires mixing box mode = | Write | ||
| AV | 111 | DryModeDischTempSpOcc | Dry mode discharge temperature setpoint when occupied | Write | ||
| AV | 112 | DryModeDischTempSpUnocc | Dry mode discharge temperature setpoint when unoccupied | Write | ||
| AV | 113 | DryModeDewPointSP | Dry mode dew point setpoint | Write | ||
| AV | 114 | DryModeOAPercent | Dry mode outdoor air percentage | Write | ||
| AV | 115 | StaticPressureLowOcc | Static Pressure Low setpoint when occupied | Write | ||
| AV | 116 | StaticPressureLowUnocc | Static Pressure Low setpoint when unoccupied | Write | ||
| AV | 117 | StaticPressureHighOcc | Static Pressure High setpoint when occupied | Write | ||
| AV | 118 | StaticPressureHighUnocc | Static Pressure High setpoint when unoccupied | Write | ||
| AI | 119 | OutdoorStatTemp | Outdoor temperature | Read | ||
| AI | 120 | ReturnStatTemp | Return temperature | Read | ||
| AImin | 121 | DischargeStatTemp | Discharge temperature | Read | ||
| AI | 122 | IntakeStatTemp | Intake temperature | Read | ||
| AI | 123 | SpaceStatTemp | Space temperature (thermistor) | Read | ||
| AI | 124 | Hmi1Temp | Unit HMI temperature | Read | ||
| AI | 125 | Hmi2Temp | Remote HMI 1 temperature | Read | ||
| AI | 126 | Hmi3Temp | Remote HMI 2 temperature | Read | ||
| AI | 127 | Hmi4Temp | Remote HMI 3 temperature | Read | ||
| AI | 128 | Hmi5Temp | Remote HMI 4 temperature | Read | ||
| AI | 129 | IntakeRh | Intake relative humidity | Read | ||
| AI | 130 | SpaceRh | Space relative humidity | Read | ||
| AI | 131 | AdjustableDamperPosition | Mixing Box Damper signal | Read | ||
| AI | 132 | Hmi1Rh | Unit HMI relative humidity | Read | ||
| AI | 133 | Hmi2Rh | Remote HMI 1 relative humidity | Read | ||
| AI | 134 | Hmi3Rh | Remote HMI 2 relative humidity | Read | ||
| AI | 135 | Hmi4Rh | Remote HMI 3 relative humidity | Read | ||
| AI | 136 | Hmi5Rh | Remote HMI 4 relative humidity | Read | ||
| AImin | 137 | ActiveFault1Id | Active Fault Code (see fault code table) | Read | ||
| AI | 138 | ActiveFault2Id | Active Fault Code (see fault code table) | Read | ||
| AI | 139 | ActiveFault3Id | Active Fault Code (see fault code table) | Read | ||
| AI | 140 | ActiveFault4Id | Active Fault Code (see fault code table) | Read | ||
| AI | 141 | ActiveFault5Id | Active Fault Code (see fault code table) | Read | ||
| AI | 142 | ActiveFault6Id | Active Fault Code (see fault code table) | Read | ||
| AImin | 143 | CurrentHvacState | HVAC State (Idle = 0, Blower = 1, Heating = 2, Cooling | Read | 0=Idle, 1=Blower, 2=Heating, 3=Cooling | |
| AI | 144 | OccupiedbySchedule | Occupied due to the schedule | Read | ||
| AI | 145 | OccupiedbyInput | Occupied due to hardware input | Read | ||
| AI | 146 | OccupiedbyDDC | Occupied due to DDC command | Read | ||
| AI | 147 | OccupiedbyHMIOverride | Occupied due to HMI command | Read | ||
| AImin | 148 | CurrentOccupiedStatus | Occupancy status, occupied = 1, unoccupied = 0 | Read | 0=Unoccupied, 1=Occupied | |
| AI | 149 | CalculatedAverageSpaceTemp | Average space temperature | Read | ||
| AI | 150 | BlowerVFDFrequency | Blower VFD frequency | Read | ||
| AI | 151 | BlowerVFDCurrent | Blower VFD current | Read | ||
| AI | 152 | BlowerVFDPower | Blower VFD power | Read | ||
| AI | 153 | CalculatedAverageRh | Average space relative humidity | Read | ||
| AImin | 154 | GasValveOutput | Controller output to the modulating gas valve. 0% = Low Fire, 100% | Read | ||
| AI | 155 | CFMReading | Fan CFM Reading | Read | ||
| AI | 156 | StaticOaPsLowOcc | Static Outdoor Air Pressure Low (Occupied) | Read | ||
| AI | 157 | StaticOaPsLowUnocc | Static Outdoor Air Pressure Low (Unoccupied) | Read | ||
| AI | 158 | StaticOaPsHighOcc | Static Outdoor Air Pressure High (Occupied) | Read | ||
| AI | 159 | StaticOaPsHighUnocc | Static Outdoor Air Pressure High (Unoccupied) | Read | ||
| AI | 160 | PressureSensor1 | Duct Static Pressure | Read | ||
| AI | 161 | PressureSensor2 | Building Static Pressure | Read |
No points match these filters.
Integration notes
- Write BV-8 SchedulingEnabled once, set schedule AVs 61-102 to 1440 (no schedule), then use BV-7 DDCOccupiedOverride for occupancy.
- DDC command points (BV-1..5, AV-6) require the heat/cool tempering modes (AV-9..12) set to DDC (3); heat and cool can't be called together.
- Factory setting points (modes, limits) should not be written routinely.
- Temperatures are F or C per the unit's Temp Units setting; the guide gives no engineering units.
- Fault AIs 137-142 report codes from the guide's DDC fault list.
Check it against the live device. A points list tells you what the controller can expose; the unit in front of you may differ by firmware or installed options. Easy BACnet scans a network for BACnet IP devices from an Android phone, reads every object on the MUA Heater DDC (Protocessor BACnet) and exports what it actually has to Excel — free. New to BACnet? Start with what a BACnet points list is and what the object types mean.
Questions about the CaptiveAire MUA Heater DDC (Protocessor BACnet)
How many BACnet points does the CaptiveAire MUA Heater DDC (Protocessor BACnet) have?
This list has 161 BACnet objects: 43 analog inputs, 111 analog values, 7 binary values. The exact set on a given unit depends on its firmware, installed options and configuration.
Which CaptiveAire MUA Heater DDC (Protocessor BACnet) BACnet points are writable?
118 of the 161 objects accept a write. Points marked Command have a priority array: a write holds until it is released, so release it back to automatic when you are done.
Where is the official CaptiveAire MUA Heater DDC (Protocessor BACnet) BACnet documentation?
The source is DDC Application Guide for MUA Heater Units, revision 2024-10, published free by CaptiveAire at https://www.captiveaire.com/catalogcontent/fans/sup_ad/doc/ddc-application-guide.pdf.
What are the minimum BACnet points to integrate the CaptiveAire MUA Heater DDC (Protocessor BACnet)?
Start with BV 7 DDCOccupiedOverride (Occupied/unoccupied command from the BMS); BV 8 SchedulingEnabled (Must be on (once) for BV-7 to work); AV 45 DischargeHeatOccSP (Occupied discharge heating setpoint); AI 143 CurrentHvacState (Idle / blower / heating / cooling state); AI 148 CurrentOccupiedStatus (Confirms the occupancy command took effect); AI 121 DischargeStatTemp (Discharge air temperature); AI 154 GasValveOutput (Burner modulation level); AI 137 ActiveFault1Id (First active fault code).
How do I enable BMS control of the CaptiveAire MUA Heater DDC (Protocessor BACnet)?
BV-8 SchedulingEnabled must be on and the internal schedule AVs (61-102) all set to 1440 so BV-7 has full control of occupancy. DDC commands (BV-1..5, AV-6) work only with the heat/cool tempering modes (AV-9..12) set to DDC; this disables temperature-based activation and heat and cool cannot be called together.
How do I check these points on the real MUA Heater DDC (Protocessor BACnet)?
Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.
More CaptiveAire BACnet points lists
- Kitchen hood demand control ventilation (DCV) controller (exhaust and make-up air fans)
CaptiveAire DCV Package DDC (Protocessor BACnet)
CaptiveAire demand control ventilation packages that run kitchen hood exhaust and supply (make-up air) fans, with the factory BACnet option.
Also known as: CaptiveAire DCV, Demand Control Ventilation, DCV Packages Network, Kitchen hood DCV, CASlink, Protocessor, CN0861 - Rooftop unit / DOAS controller
CaptiveAire Paragon RTU / DOAS DDC (Protocessor BACnet)
CaptiveAire Paragon HVAC series packaged rooftop units and dedicated outdoor air systems with the factory DDC package.
Also known as: Paragon, CaptiveAire DOAS, CaptiveAire RTU, Protocessor, CN0861, RTU DDC Points - Kitchen hood self-cleaning wash system control panel
CaptiveAire Self Cleaning System (SCS) Control Panel
CaptiveAire Self Cleaning System panels that hot-water wash or cold-water mist kitchen exhaust hoods and plenums, and can also run the hood's fan and light zones.
Also known as: CaptiveAire SCS, Self Cleaning System, Hood wash panel, Hot Water Wash, Cold Water Mist, ECPM03, Protocessor
Source: DDC Application Guide for MUA Heater Units · rev. 2024-10. Object names, instances and units are reproduced as published; descriptions are our own.