Home
BACnet points lists
Bell & Gossett
TechnoForce e-MTV booster pump controller

Booster pump controller · BACnet points list

Bell & Gossett TechnoForce e-MTV booster pump controller BACnet points list

Updated 12 November 2026

Short answer

The TechnoForce e-MTV controller runs a variable-speed water booster set and has a small BACnet object list: Binary Values for drive not-ready and trip alarms, pump enable, pump run status, general and sensor alarms, auto/manual status, system start/stop, manual alternation and alarm reset, and Analog Inputs for discharge pressure, flow, setpoint, speed and pump run hours.

This page lists 28 BACnet objects for the Bell & Gossett TechnoForce e-MTV booster pump controller — 6 of them writable — with each object’s type, instance number, name, engineering units and access. It is re-typed from Bell & Gossett’s own free documentation, linked below.

Manufacturer: Bell & Gossett
Model: TechnoForce e-MTV booster pump controller
Equipment: Booster pump controller
Equipment type: VFDs & pumps
BACnet objects: 28 (6 writable)
Transport: BACnet IP, BACnet MS/TP
Firmware: e-MTV application 1.0 or above, FW 596.13 or above
Also known as: TechnoForce e-MTV, e-MTV, B&G TechnoForce, TechnoForce Pump Controller, IM361
Source document: TechnoForce e-MTV Instruction Manual · IM361 R1

Download CSV 28 rows Download EDE B.I.G.-EU JSON Manufacturer PDF ↗ Compare with your scan Download Easy BACnet Mobile App Google Play

Reference only, provided as-is: verify against Bell & Gossett’s current documentation and the live device before use. Not official Bell & Gossett information. Terms of use.

BMS integration notes: Bell & Gossett TechnoForce e-MTV booster pump controller

Integration in brief

Start and stop the booster with BV 18 and enable pumps with BV 6-8. Read discharge pressure, setpoint, flow and speed (AI 0-3), pump run status (BV 9-11) and the general alarm (BV 12); BV 20 resets alarms.

Minimum points to map

The short list most integrators start with — enough to run the unit from a BMS. Map more as the job needs.

Object	Name	Why	Access
BV 18	Start_Stop	System start/stop (1 = on)	Write
BV 6	Pump1EnableDisable	Pump 1 enable	Write
BV 20	AlarmReset	Alarm reset	Write
AI 0	DischargePressure	Discharge pressure	Read
AI 2	Setpoint	Pressure setpoint in use	Read
AI 3	Speed	System speed, %	Read
BV 9	Pump1RunStatus	Pump 1 running	Read
BV 17	AutoManualStatus	Auto/manual status (1 = auto)	Read
BV 12	GeneralAlarm	General alarm	Read

Enable & remote start

BV 18 Start_Stop starts and stops the system; BV 17 shows whether the controller is in auto.

Watch out for

Units for pressure and flow depend on the controller unit setting.

Bell & Gossett TechnoForce e-MTV booster pump controller BACnet objects

Type: AI, AO, AV, BI, BO, BV, MI/MO/MV (multi-state) · Access: Read read-only, Write writable, Command writable with a priority array.

28 of 28 shown

Type

AnalogBinary

Access

Units

Show

Bell & Gossett TechnoForce e-MTV booster pump controller BACnet Points List
			Description			States
BV	0	VFD1NotReady			Read	0=O.K., 1=Failure
BV	1	VFD1Trip			Read	0=O.K., 1=Failure
BV	2	VFD2NotReady			Read	0=O.K., 1=Failure
BV	3	VFD2Trip			Read	0=O.K., 1=Alarm
BV	4	VFD3NotReady			Read	0=O.K., 1=Failure
BV	5	VFD3Trip			Read	0=O.K., 1=Failure
BVmin	6	Pump1EnableDisable			Write	0=Disable, 1=Enable
BV	7	Pump2EnableDisable			Write	0=Disable, 1=Enable
BV	8	Pump3EnableDisable			Write	0=Disable, 1=Enable
BVmin	9	Pump1RunStatus			Read	0=Not Running, 1=Running
BV	10	Pump2RunStatus			Read	0=Not Running, 1=Running
BV	11	Pump3RunStatus			Read	0=Not Running, 1=Running
BVmin	12	GeneralAlarm			Read	0=O.K., 1=Failure
BV	13	AL_FTFault			Read	0=O.K., 1=Failure
BV	14	AL_PTFault			Read	0=O.K., 1=Failure
BV	15	AL_PT1Fault			Read	0=O.K., 1=Failure
BV	16	AL_PT2Fault			Read	0=O.K., 1=Failure
BVmin	17	AutoManualStatus			Read	0=Manual, 1=Auto
BVmin	18	Start_Stop			Write	0=OFFF, 1=ON
BV	19	ManualAlteration			Write	0=Off, 1=On
BVmin	20	AlarmReset			Write	0=O.K., 1=Failure
AImin	0	DischargePressure	Range 0 to Span	PSI or BAR	Read
AI	1	DischargeFlow	Range 0 to Span	GPM or M3/h	Read
AImin	2	Setpoint	Range 0 to Span	PSI or BAR	Read
AImin	3	Speed	Range 0 to 100	%	Read
AI	4	Pump1RunHour	Range 0 to Max Value	h	Read
AI	5	Pump2RunHour	Range 0 to Max Value	h	Read
AI	6	Pump3RunHour	Range 0 to Max Value	h	Read

Object ID lookup: Bell & Gossett TechnoForce e-MTV booster pump controller point IDs by name

BV0VFD1NotReady
BV1VFD1Trip
BV2VFD2NotReady
BV3VFD2Trip
BV4VFD3NotReady
BV5VFD3Trip
BV6Pump1EnableDisable
BV7Pump2EnableDisable
BV8Pump3EnableDisable
BV9Pump1RunStatus
BV10Pump2RunStatus
BV11Pump3RunStatus
BV12GeneralAlarm
BV13AL_FTFault
BV14AL_PTFault
BV15AL_PT1Fault
BV16AL_PT2Fault
BV17AutoManualStatus
BV18Start_Stop
BV19ManualAlteration
BV20AlarmReset
AI0DischargePressure
AI1DischargeFlow
AI2Setpoint
AI3Speed
AI4Pump1RunHour
AI5Pump2RunHour
AI6Pump3RunHour

Integration notes

Pressure and flow units follow the controller setting (PSI or bar, GPM or m3/h).
BV 20 AlarmReset prints the alarm state texts (1 = Failure, 0 = O.K.); write 1 to reset.
BV 18 Start_Stop states are printed "1=ON 0= OFFF".
The PICS describes communication over RS-485 or IP; the manual also has a Modbus RTU / IP point table.

Check it against the live device. A points list tells you what the controller can expose; the unit in front of you may differ by firmware or installed options. This list is provided as-is for reference only and may contain mistakes — confirming it before you write, map or commission anything is up to you (terms). Easy BACnet scans a network for BACnet IP devices from an Android phone, reads every object on the TechnoForce e-MTV booster pump controller and exports what it actually has to Excel — free. New to BACnet? Start with what a BACnet points list is and what the object types mean.

Questions about the Bell & Gossett TechnoForce e-MTV booster pump controller

How many BACnet points does the Bell & Gossett TechnoForce e-MTV booster pump controller have?

This list has 28 BACnet objects: 7 analog inputs, 21 binary values. The exact set on a given unit depends on its firmware, installed options and configuration.

Which Bell & Gossett TechnoForce e-MTV booster pump controller BACnet points are writable?

6 of the 28 objects accept a write. Points marked Command have a priority array: a write holds until it is released, so release it back to automatic when you are done.

Where is the official Bell & Gossett TechnoForce e-MTV booster pump controller BACnet documentation?

The source is TechnoForce e-MTV Instruction Manual (IM361 R1), published free by Bell & Gossett at https://www.xylem.com/siteassets/brand/bell-amp-gossett/resources/manual/technoforce-e-mtv-iom-im361-r1.pdf.

What are the minimum BACnet points to integrate the Bell & Gossett TechnoForce e-MTV booster pump controller?

Start with BV 18 Start_Stop (System start/stop (1 = on)); BV 6 Pump1EnableDisable (Pump 1 enable); BV 20 AlarmReset (Alarm reset); AI 0 DischargePressure (Discharge pressure); AI 2 Setpoint (Pressure setpoint in use); AI 3 Speed (System speed, %); BV 9 Pump1RunStatus (Pump 1 running); BV 17 AutoManualStatus (Auto/manual status (1 = auto)); BV 12 GeneralAlarm (General alarm).

How do I enable BMS control of the Bell & Gossett TechnoForce e-MTV booster pump controller?

BV 18 Start_Stop starts and stops the system; BV 17 shows whether the controller is in auto.

How do I check these points on the real TechnoForce e-MTV booster pump controller?

Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.

More Bell & Gossett BACnet points lists

Source: TechnoForce e-MTV Instruction Manual · IM361 R1. Object names, instances and units are reproduced as published; descriptions are our own.