Home
BACnet points lists
Tigerflow
Mark V booster pump controller

Booster pump system controller · BACnet points list

Tigerflow Mark V booster pump controller BACnet points list

Updated 12 November 2026

Short answer

The Mark V is the controller on Tigerflow multi-pump booster packages (up to four VFD pumps). Its BACnet list is monitoring only: every object is read-only. It reports pump run commands and VFD run feedback, HOA positions, pump faults, pressure alarms, suction and system pressure, the pressure setpoint, flow, per-pump speed and run hours.

This page lists 47 BACnet objects for the Tigerflow Mark V booster pump controller — 0 of them writable — with each object’s type, instance number, name, engineering units and access. It is re-typed from Tigerflow’s own free documentation, linked below.

Manufacturer: Tigerflow
Model: Mark V booster pump controller
Equipment: Booster pump system controller
Equipment type: VFDs & pumps
BACnet objects: 47 (0 writable)
Transport: —
Firmware: Not stated
Also known as: Mark V, Mark 5, Tigerflow Mark V, Mark V booster, Tigerflow booster pump controller
Source document: MARK V - BACNET POINT LIST · rev. 2018-04-19

Download CSV 47 rows Download EDE B.I.G.-EU JSON Manufacturer PDF ↗ Compare with your scan Download Easy BACnet Mobile App Google Play

Reference only, provided as-is: verify against Tigerflow’s current documentation and the live device before use. Not official Tigerflow information. Terms of use.

BMS integration notes: Tigerflow Mark V booster pump controller

Integration in brief

Monitoring only. Map system and suction pressure, the active setpoint and flow, the per-pump run commands and faults, and the general and fatal alarm flags.

Minimum points to map

The short list most integrators start with — enough to run the unit from a BMS. Map more as the job needs.

Object	Name	Why	Access
AV 2	System Pressure	System discharge pressure, psi	Read
AV 3	Pressure Set Point	Active pressure setpoint, psi (read-only)	Read
AV 1	Suction Pressure	Suction pressure, psi	Read
AV 4	Flow Rate	System flow, gpm	Read
BV 17	Pump 1 Run Command	Pump 1 called to run (repeat for pumps 2-4)	Read
AV 5	Pump 1 Speed Signal (%)	Pump 1 speed signal, % (repeat for pumps 2-4)	Read
BV 51	Pump 1 Fault	Pump 1 fault (repeat for pumps 2-4)	Read
BV 63	General Alarm	Any general alarm	Read
BV 64	Fatal Alarm	Fatal alarm active	Read

Watch out for

Every object is read-only, so there is no BMS enable or setpoint write on the Mark V; use the hard-wired remote disable input if the BMS must stop the system.

Tigerflow Mark V booster pump controller BACnet objects

Type: AI, AO, AV, BI, BO, BV, MI/MO/MV (multi-state) · Access: Read read-only, Write writable, Command writable with a priority array.

47 of 47 shown

Type

AnalogBinary

Units

Show

Tigerflow Mark V booster pump controller BACnet Points List
			Description			States
BV	1	VFD 1 Run Status Input	Run status input from VFD 1		Read	1=On
BV	2	VFD 2 Run Status Input	Run status input from VFD 2		Read	1=On
BV	3	VFD 3 Run Status Input	Run status input from VFD 3		Read	1=On
BV	4	VFD 4 Run Status Input	Run status input from VFD 4		Read	1=On
BV	5	Remote System Disable Input	Hard-wired remote disable input		Read	1=On
BV	6	Phase Loss Sensor Input	Phase loss sensor input		Read	1=On
BV	7	Flow Switch Input	Flow switch input		Read	1=On
BV	8	Level Switch Input	Level switch input		Read	1=On
BVmin	17	Pump 1 Run Command	Controller run output to pump 1		Read	1=On
BV	18	Pump 2 Run Command	Controller run output to pump 2		Read	1=On
BV	19	Pump 3 Run Command	Controller run output to pump 3		Read	1=On
BV	20	Pump 4 Run Command	Controller run output to pump 4		Read	1=On
BV	21	General/Fatal Alarm Output	General or fatal alarm relay output		Read	1=On
BV	22	Alarm Horn Output	Alarm horn output		Read	1=On
BV	33	Pump 1 in Auto	Pump 1 HOA in Auto		Read	1=On
BV	34	Pump 1 in Hand	Pump 1 HOA in Hand		Read	1=On
BV	35	Pump 2 in Auto	Pump 2 HOA in Auto		Read	1=On
BV	36	Pump 2 in Hand	Pump 2 HOA in Hand		Read	1=On
BV	37	Pump 3 in Auto	Pump 3 HOA in Auto		Read	1=On
BV	38	Pump 3 in Hand	Pump 3 HOA in Hand		Read	1=On
BV	39	Pump 4 in Auto	Pump 4 HOA in Auto		Read	1=On
BV	40	Pump 4 in Hand	Pump 4 HOA in Hand		Read	1=On
BVmin	51	Pump 1 Fault	Pump 1 fault		Read	1=On
BV	52	Pump 2 Fault	Pump 2 fault		Read	1=On
BV	53	Pump 3 Fault	Pump 3 fault		Read	1=On
BV	54	Pump 4 Fault	Pump 4 fault		Read	1=On
BV	55	Phase Loss Alarm	Phase loss alarm		Read	1=On
BV	56	Low Suction Pressure Alarm	Low suction pressure alarm		Read	1=On
BV	57	Low System Pressure Alarm	Low system pressure alarm		Read	1=On
BV	58	High System Pressure Alarm	High system pressure alarm		Read	1=On
BV	59	System Pressure Sensor Failure Alarm	System pressure transducer failure		Read	1=On
BV	60	Suction Pressure Sensor Failure Alarm	Suction pressure transducer failure		Read	1=On
BV	62	Alarm Silenced	Alarm horn silenced		Read	1=On
BVmin	63	General Alarm	General alarm active		Read	1=On
BVmin	64	Fatal Alarm	Fatal alarm active		Read	1=On
AVmin	1	Suction Pressure	Pump suction pressure	psi	Read
AVmin	2	System Pressure	System (discharge) pressure	psi	Read
AVmin	3	Pressure Set Point	Active system pressure setpoint	psi	Read
AVmin	4	Flow Rate	System flow rate	gpm	Read
AVmin	5	Pump 1 Speed Signal (%)	Speed signal to pump 1 VFD	%	Read
AV	6	Pump 2 Speed Signal (%)	Speed signal to pump 2 VFD	%	Read
AV	7	Pump 3 Speed Signal (%)	Speed signal to pump 3 VFD	%	Read
AV	8	Pump 4 Speed Signal (%)	Speed signal to pump 4 VFD	%	Read
AV	9	Pump 1 Run Time (Hrs.)	Pump 1 run hours	h	Read
AV	10	Pump 2 Run Time (Hrs.)	Pump 2 run hours	h	Read
AV	11	Pump 3 Run Time (Hrs.)	Pump 3 run hours	h	Read
AV	12	Pump 4 Run Time (Hrs.)	Pump 4 run hours	h	Read

Object ID lookup: Tigerflow Mark V booster pump controller point IDs by name

BV1VFD 1 Run Status Input
BV2VFD 2 Run Status Input
BV3VFD 3 Run Status Input
BV4VFD 4 Run Status Input
BV5Remote System Disable Input
BV6Phase Loss Sensor Input
BV7Flow Switch Input
BV8Level Switch Input
BV17Pump 1 Run Command
BV18Pump 2 Run Command
BV19Pump 3 Run Command
BV20Pump 4 Run Command
BV21General/Fatal Alarm Output
BV22Alarm Horn Output
BV33Pump 1 in Auto
BV34Pump 1 in Hand
BV35Pump 2 in Auto
BV36Pump 2 in Hand
BV37Pump 3 in Auto
BV38Pump 3 in Hand
BV39Pump 4 in Auto
BV40Pump 4 in Hand
BV51Pump 1 Fault
BV52Pump 2 Fault
BV53Pump 3 Fault
BV54Pump 4 Fault
BV55Phase Loss Alarm
BV56Low Suction Pressure Alarm
BV57Low System Pressure Alarm
BV58High System Pressure Alarm
BV59System Pressure Sensor Failure Alarm
BV60Suction Pressure Sensor Failure Alarm
BV62Alarm Silenced
BV63General Alarm
BV64Fatal Alarm
AV1Suction Pressure
AV2System Pressure
AV3Pressure Set Point
AV4Flow Rate
AV5Pump 1 Speed Signal (%)
AV6Pump 2 Speed Signal (%)
AV7Pump 3 Speed Signal (%)
AV8Pump 4 Speed Signal (%)
AV9Pump 1 Run Time (Hrs.)
AV10Pump 2 Run Time (Hrs.)
AV11Pump 3 Run Time (Hrs.)
AV12Pump 4 Run Time (Hrs.)

Integration notes

All 47 objects are printed as Read Only; the BMS cannot start, stop or reset the system over BACnet on the Mark V.
Instances are printed as BV0001.. / AV0001..; the gaps (BV 9-16, 23-32, 41-50, 61) are not in the list.
The point list does not state the BACnet transport (IP or MS/TP) or device addressing.
Units as printed: pressures in psi, flow in GPM, run time in hours.

Check it against the live device. A points list tells you what the controller can expose; the unit in front of you may differ by firmware or installed options. This list is provided as-is for reference only and may contain mistakes — confirming it before you write, map or commission anything is up to you (terms). Easy BACnet scans a network for BACnet IP devices from an Android phone, reads every object on the Mark V booster pump controller and exports what it actually has to Excel — free. New to BACnet? Start with what a BACnet points list is and what the object types mean.

Questions about the Tigerflow Mark V booster pump controller

How many BACnet points does the Tigerflow Mark V booster pump controller have?

This list has 47 BACnet objects: 12 analog values, 35 binary values. The exact set on a given unit depends on its firmware, installed options and configuration.

Which Tigerflow Mark V booster pump controller BACnet points are writable?

None of the listed objects are marked writable in the source documentation.

Where is the official Tigerflow Mark V booster pump controller BACnet documentation?

The source is MARK V - BACNET POINT LIST, revision 2018-04-19, published free by Tigerflow at https://tigerflow.com/demo/wp-content/uploads/2018/05/Mark-V-BACNet-Point-List-20180419-1.pdf.

What are the minimum BACnet points to integrate the Tigerflow Mark V booster pump controller?

Start with AV 2 System Pressure (System discharge pressure, psi); AV 3 Pressure Set Point (Active pressure setpoint, psi (read-only)); AV 1 Suction Pressure (Suction pressure, psi); AV 4 Flow Rate (System flow, gpm); BV 17 Pump 1 Run Command (Pump 1 called to run (repeat for pumps 2-4)); AV 5 Pump 1 Speed Signal (%) (Pump 1 speed signal, % (repeat for pumps 2-4)); BV 51 Pump 1 Fault (Pump 1 fault (repeat for pumps 2-4)); BV 63 General Alarm (Any general alarm); BV 64 Fatal Alarm (Fatal alarm active).

How do I check these points on the real Mark V booster pump controller?

Scan the network with a BACnet IP browser such as Easy BACnet, open the device and compare its object list with this table. Anything missing is usually an option that isn't installed or a point that is disabled in the controller's configuration.

More Tigerflow BACnet points lists

Pump system controller (variable speed, differential pressure)
Tigerflow Mark VI pump system controller
Tigerflow packaged variable-speed pump systems run by the Mark VI controller with up to three VFD pumps and zone differential pressure sensors.
49 objects · 4 writable
Also known as: Mark VI, Mark 6, Tigerflow Mark VI, Tigerflow differential pressure pump controller

Source: MARK V - BACNET POINT LIST · rev. 2018-04-19. Object names, instances and units are reproduced as published; descriptions are our own.